Platinum Powder Coating

1. Product Overview

This product takes polyester resin and epoxy resin as the main base materials, integrating the excellent decorative performance, mechanical properties and good corrosion resistance of both epoxy and polyester.

1.1 STD. Platinum FEVE Fluoropolymer Powder Coating

Innovative Powder Coatings that Perform as Well as They Look

STD. Platinum represents a breakthrough in powder coating technology. Coatings offer FGIA/AAMA 2605 compliance, backed by more than 10 years of test data (Florida), and a high transfer efficiency rate that is 20% higher than standard FEVE powders. But that’s just the beginning—follow along below to learn more about the color and performance benefits available for architectural and extrusion sheet aluminum.

1.1.1 A New Study of Competing FEVE Fluoropolymer Coatings

A recent study demonstrates that STD. Platinum powder is in a class of its own. Compared to other hyper-durable products on the market, STD. Platinum exhibited twenty times the color retention of competitors’ FEVE powder coatings. New data indicates that STD. Platinum maintains its performance significantly at the five-year mark, whereas competing architectural powder coatings show a notable decline in color stability.

STD. Platinum FEVE fluoropolymer powder coatings were designed with color fastness and longevity in mind.

1.1.2 Benefits

• Superior Color Retention: Compared to other hyper-durable products, STD. Platinum showed twenty times the color retention of competitors.

• Minimal Color Loss: STD. Platinum exhibited only a 6% loss in color retention over a five-year period, while similarly colored competitor products demonstrated more than a 100% loss in color retention in the same period.

• High Transfer Efficiency: Over 20% improvement over standard FEVE powder, resulting in less waste and better coverage.

• Extended Gloss Range: 5 – 85, compared to 25 – 70 for standard FEVE products.

• Reduced Oven Emissions: 70% less e-cap (oven smoke and oven build-up).

• Improved Corrosion Performance: On aluminum in a single coat.

• Wide Selection of Colors and Effects: Including popular anodized metal finishes.

1.1.3 Environmental Benefits

Specifically formulated without the following substances:

• Triglycidyl isocyanurate (TGIC)

• Perfluorooctanoic acid (PFOA)

• Fluorosurfactants

• Volatile organic compounds (VOCs)

• Hazardous air pollutants (HAPs)

• Living Building Challenge (LBC) Red List substances

REACH Compliant: Free of Substances of Very High Concern (SVHCs)

1.1.4 Typical Uses

• Window frames

• Building panels

• Storefronts

1.2 Magic Color Metal Powder Coating Series

This series of products is made of special materials supplemented by high-end magic color metal materials. The coating film is highly protective, brilliant, and charming. The visual effect presented by this product is like a well-cut gem formed in the mantle layer of the earth—it is bright and starry, with wonderful three-dimensional optical dimensions and tones, and is deeply loved by the market.

1.1 STD. Platinum FEVE Fluoropolymer Powder Coating

STD. Platinum represents a breakthrough in powder coating technology. Coatings offer FGIA/AAMA 2605 compliance, backed by more than 10 years of test data (Florida), and a high transfer efficiency rate that is 20% higher than standard FEVE powders. But that’s just the beginning—follow along below to learn more about the color and performance benefits available for architectural and extrusion sheet aluminum.

1.1.1 A New Study of Competing FEVE Fluoropolymer Coatings

A recent study demonstrates that STD. Platinum powder is in a class of its own. Compared to other hyper-durable products on the market, STD. Platinum exhibited twenty times the color retention of competitors’ FEVE powder coatings. New data indicates that STD. Platinum maintains its performance significantly at the five-year mark, whereas competing architectural powder coatings show a notable decline in color stability.

STD. Platinum FEVE fluoropolymer powder coatings were designed with color fastness and longevity in mind.

1.1.2 Benefits

• Superior Color Retention: Compared to other hyper-durable products, STD. Platinum showed twenty times the color retention of competitors.

• Minimal Color Loss: STD. Platinum exhibited only a 6% loss in color retention over a five-year period, while similarly colored competitor products demonstrated more than a 100% loss in color retention in the same period.

• High Transfer Efficiency: Over 20% improvement over standard FEVE powder, resulting in less waste and better coverage.

• Extended Gloss Range: 5 – 85, compared to 25 – 70 for standard FEVE products.

• Reduced Oven Emissions: 70% less e-cap (oven smoke and oven build-up).

• Improved Corrosion Performance: On aluminum in a single coat.

• Wide Selection of Colors and Effects: Including popular anodized metal finishes.

1.1.3 Environmental Benefits

Specifically formulated without the following substances:

• Triglycidyl isocyanurate (TGIC)

• Perfluorooctanoic acid (PFOA)

• Fluorosurfactants

• Volatile organic compounds (VOCs)

• Hazardous air pollutants (HAPs)

• Living Building Challenge (LBC) Red List substances

REACH Compliant: Free of Substances of Very High Concern (SVHCs)

1.1.4 Typical Uses

• Window frames

• Building panels

• Storefronts

This series of products is made of special materials supplemented by high-end magic color metal materials. The coating film is highly protective, brilliant, and charming. The visual effect presented by this product is like a well-cut gem formed in the mantle layer of the earth—it is bright and starry, with wonderful three-dimensional optical dimensions and tones, and is deeply loved by the market.

2. Basic Business Information

Item	Details
Location	China
Business Type	Manufacturer, Exporter
Brand	Standard
Certificate	ACS, NSF, QUALICAOT, WRAS, KTW
Payment and Delivery Terms	30% advance payment, 70% before delivery
Minimum Order Quantity	100kg
Price	Negotiable
Delivery Time	7-10 days
Payment Method	T/T, L/C

3. Product Features

3.1 Standard Powder Coating

• Excellent mechanical properties (including impact resistance, hardness, toughness, adhesion, etc.)

• Good leveling property and glossiness

• Strong corrosion resistance

3.2 Magic Color Metal Powder Coating

• 360° coating film: 360° viewing angle has a strong metallic feel and extremely high decorativeness

• Excellent stability and strong protection

• Alkali resistance, weather resistance and excellent corrosion resistance

4. Application Areas

4.1 Standard Powder Coating

Household appliances, communication equipment units, indoor fitness equipment, tool boxes, filing cabinets, shelves, lamps, etc.

Aluminum alloy profiles, aluminum system doors and windows, aluminum veneers, aluminum ceilings, aluminum curtain walls, etc., as well as high-end household appliances, industrial products, car wheels, etc.

4.2 Magic Color Metal Powder Coating

4.3 STD. Platinum FEVE Fluoropolymer Powder Coating

4.3 STD. Platinum FEVE Fluoropolymer Powder Coating

Architectural and extrusion sheet aluminum, window frames, building panels, storefronts, etc.

Aluminum alloy profiles, aluminum system doors and windows, aluminum veneers, aluminum ceilings, aluminum curtain walls, etc., as well as high-end household appliances, industrial products, car wheels, etc.

5. Product Series

• Available types: standard curing type and low temperature curing type

• Customizable: various gloss levels and colors

• Diversified textures: flat surface, art texture, metal effect, antique style, etc.

• Special series: Magic color metal powder coating, STD. Platinum FEVE fluoropolymer powder coating

6. Technical Parameters

6.1 Mechanical Properties (Standard Powder Coating)

Test Items	Test Standards	Performance Indicators
Pencil hardness	GB/T6739-1996	>H
Adhesion	GB/T9286-1998	Grade 0
Bending	GB6742-86	3mm
Impact	GB/T1732-93	50kg.cm
Cupping	GB9753-88	>6mm

6.2 Corrosion Resistance (Standard Powder Coating)

Test Items	Test Standards	Performance Indicators
Salt spray resistance	GB/T1771-91	No change in coating after 500 hours; single-side isolation at specification <2mm
Moisture and heat resistance	GB/T1740-79	>500 hours slight gloss loss, ≤Grade 1

6.3 Performance Indicators (Magic Color Metal Powder Coating)

Type	Item	Test Standard	Index
Powder Performance	State in Container	HG/T2006-2006	Uniform color, no foreign matter, loose powder
Sieve residue (125μm)	HG/T2006-2006	All passed
Coating Mechanical Properties	Adhesion	GB/T9286	Grade 0
Impact Resistance	GB/T1732	Punch Diameter:16±0.3mm；Depth of pit 2.5±0.3mm, no peeling after tape pull test
Cupping resistance	GB/T 9753	5mm
Bending resistance	GB/T 6742	5mm After the tape pull test, there is no peeling
Chemical properties of the coating film	Boiling water resistance	GB5237.4	No peeling or wrinkling
Solvent resistance	GB5237.4	Grade 3
Salt spray resistance	GB/T10125	1000h, at the line: unidirectional rust ≤4mm
Moisture and heat resistance	GB/T1740	1000h no blistering, peeling or other obvious changes
Weather resistance of the coating film	Accelerated weather resistance	GB/T1865	Negotiated, can pass the 4000h test
Natural weather resistance	GB/T9276	Negotiated

Note: The above parameters are laboratory data for reference only. Actual indicators are related to factors such as customer environment, equipment, materials, pretreatment, and spraying process.

6.4 Powder Performance

Specific gravity: 1.1~1.8g/cm³

7. Application Conditions

7.1 Standard Powder Coating

• Pretreatment: phosphating, chromating

• Coating methods: suitable for high-voltage electrostatic spraying, friction electrostatic spraying, electrostatic fluidized bed spraying, fluidized bed dipping

• Curing conditions: 140℃ for 30 minutes

• 180℃ for 15 minutes

• 200℃ for 10 minutes

Can also be customized according to customer needs

7.2 Magic Color Metal Powder Coating - Guide to Use

7.2.1 Curing conditions

200℃/10min; In order to make the coating film of the coated object cure evenly and the gloss stable, it is best to make the temperature distribution in the baking furnace uniform; and reasonably control the curing temperature and time according to the situation of the workpiece.

7.2.2 Pretreatment

The workpiece must be pretreated before spraying, and it must comply with the provisions of Chapter 5 of GB/T 8013.3-2007. The mass of the chromate conversion film should be between 0.4 and 1.0 g/㎡. The time interval between chemical conversion pretreatment and coating should not exceed 16 hours. In principle, coating should be applied immediately after the conversion treatment is dry.

7.2.3 Workpiece hanging

When hanging the workpiece, hang it reasonably according to the shape and thickness of the workpiece to improve the powdering rate and yield; and pay attention to keeping the spraying system and the surrounding environment clean to prevent different brands of powder coating from mixing and affecting the surface effect of the coating.

7.2.4 Powder spraying

Choose reasonable process parameters, control the voltage, air pressure and powder output. The powder spraying environment should preferably have a temperature and humidity control system. The optimal powder spraying temperature is 15-25℃, and the relative air humidity of the powder spraying room is preferably 45%-55%; in addition, the proportion of recycled powder should be controlled to ensure the color stability of the product.

The recommended coating thickness is 60-80um, otherwise it will affect the performance of the coating.

During the film formation process, the color will be slightly affected by process conditions such as temperature and thickness. It is recommended that users conduct tests before use to achieve satisfactory results.

8. Packaging and Storage

8.1 Standard Powder Coating

• Packaging type: carton packaging

• Net weight: 20kg/box

• Inner lining: polyethylene plastic bag

• Storage: Store in a dry, ventilated room below 30°C; avoid direct sunlight; shelf life: under the above conditions, the powder can be stably stored for 6 months

8.2 Magic Color Metal Powder Coating

The outer packaging of powder coating is a hard carton lined with a plastic bag, with a net weight of 25KG and 20KG per box. It should be stored at an ambient temperature below 30℃, and the storage environment should be kept ventilated and dry, and the powder should be prevented from direct sunlight. The location where the powder is stored is not allowed to be close to fire and away from heat sources.

9. Safety and Health

9.1 Standard Powder Coating

• All raw materials of the powder coating do not contain toxic substances.

• No toxic gas is released during baking.

• Avoid inhalation of dust during use; operators should wear dust masks.

• Minimize long-term contact between skin and powder; paint attached to the skin can be washed with soap.

9.2 Magic Color Metal Powder Coating - Safety Measures

This product is non-flammable and explosive, basically non-toxic, and must not be ingested.

10. Contact Us

If you're ready to take the next step, Leave your message below and we’ll reply soon. 20+ years of chemical manufacturing & export experience, a partner you can trust.

Other supplier products

	Metal powder coating	Product introduction “Paint to powder” special varieties, stable color, strong metal effect, good adhesion to metal substrate; Metal ...
	Exterior durable polyester powder coatings with antimicrobial technology MT-610 AM	Product description MT-610 AM is a range of polyester TGIC Free powder coatings designed for exterior exposure with good weather resistance from j...
	Polyester-Epoxy Powder Coating	Product Introduction:This series of products is a thermosetting powder coating formulated from a mixture of saturated polyester resin, correspondin...
	Far-Infrared Functional Powder Coating	Product Features: Far-infrared rays have a vibration frequency close to that of human cell molecules, which is significant for human survival and ...
	Household electrical appliances powder coating	Features: ◆ Smooth surface effect ◆ Excellent physical and mechanical properties ◆ Excellent heat resistance and chemical resistance Product se...

All supplier products

Same products

	Trimellitic anhydride 97%	Seller: Yufeng International Group Co., Ltd	Trimellitic anhydrideis a 2-benzofuran compound having oxo groups at the 1- and 3-positions and a...
	Isobutyric Anhydride CAS 97-72-3	Seller: Yufeng International Group Co., Ltd	Product Name: Isobutyric Anhydride CAS No.: 97-72-3 Purity: 99% Molecular Formula: C6H10O3 Mo...
	Isobutyric Acid CAS 79-31-2	Seller: Yufeng International Group Co., Ltd	Product Name:ISOBUTYRIC ACID Synonyms: 2-Methylpropanoic acid 79-31-2 Isobutanoic acid 2-Met...
	2-Amino-2-methyl-1-propanol（AMP）CAS：124-68-5	Seller: Yufeng International Group Co., Ltd	AtYufeng, a trusted 2-Amino-2-methyl-1-propanol Factory & Supplier, we prioritize quality and...
	Dimethyl sulfoxide (DMSO) CAS: 67-68-5	Seller: Yufeng International Group Co., Ltd	Yufengis one of the leading dimethyl sulfoxide suppliers and also a professional such manufacture...