Polyester based powder coatings MT-620 AM
Product Description
MT-620 AM is a series of polyester based powder coatings, formulated without the use of TGIC, designed for the exterior environment, offering the benefits of MT 600 in combination with specific antimicrobial activity. MT-620 AM powders are available in a wide range of colors in gloss, satin, matt, metallic and textured effects and can be custom matched to the user’s requirements.
Powder properties
| Typical value | |
| Chemical Type | Polyester – TGIC Free |
| Density | 1.2 – 1.9 g/cm³, depending on colour and effect |
| Application | Suitable for electrostatic spray |
| Shelf life | 24 months below 30 °C
12 months below 35 °C |
| Storage Conditions | Under dry, cool (≤ 30°C) conditions
(open boxes must be resealed) |
| Curing schedule | 30-40 min at 170°C
10-20 min at 180°C 8-16 min at 200°C (at object temperature) |
Test conditions
The results shown below are based on mechanical and chemical tests which (unless otherwise indicated) have been carried out under laboratory conditions and are given for guidance only. Actual product performance will depend upon the circumstances under which the product is used.
| Pre-treatment | Gold Seal lightweight Zinc Phosphate |
| Substrate | Gold Seal polished 0.5mm steel |
| Curing schedule
(Object Temperature) |
10 minutes at 200°C |
| Film Thickness | 50 microns |
Mechanical tests
| Adhesion | ISO 2409 (2mm crosshatch) | Gt 0 |
| Erichsen cupping | ISO 1520 | ≥ 7 mm |
| Flexibility | ISO 1519 | Pass 5mm |
| Hardness | Pass – no penetration to substrate | ISO 1518-1 (2000g) |
| Impact | ISO 6272 | > 50 kg·cm direct |
Pretreatment
Aluminium, steel or Zintec surfaces to be coated must be clean and free from grease. Iron phosphate and particularly lightweight zinc phosphating of ferrous metals improves corrosion resistance. Aluminium substrates may require a chromate conversion coating. Detailed advice should be sought from the pre-treatment supplier.
Application
MT-620 AM powder coatings can be applied by corona electrostatic equipment. In all application processes the aspect obtained is subject to variation, depending on the method of application (type of gun, nozzle, etc) and the shape/type of component. We recommend that the actual application parameters are adapted and adjusted depending on the type of component and with each powder batch to give a finish in accordance with our color card. The following procedure is given as a guideline when using these finishes. We recommend the use of flat jet spray nozzles. To ensure powder homogeneity, the complete content of the boxes should be emptied completely into the feed hopper. For manual application it is essential to ensure that an even film thickness is applied, and, in all Instances, sinusoidal gun movements should be avoided. All powders can show small color differences from batch to batch, this is normal and unavoidable. Applicators and fabricators are advised to use a single batch for parts that will be assembled together. Differences are more likely with special effect powders. Bonded products have better application properties than blended products (more stable) but attention should still be paid to line settings to avoid “marble effect” and changes in aspect after recycling. Different substrates (Aluminium, steel, galvanized steel, etc.), use of primer, and big changes in film thickness may give a different aspect. Products with different codes should not be mixed even if same color and gloss.
If you're ready to take the next step, Leave your message below and we’ll reply soon. 20+ years of chemical manufacturing & export experience, a partner you can trust.
在线联系供应商
Other supplier products
 |
Building Materials Super Weather Resistant Powder | Powder characteristics With excellent weather resistance, it not only has the characteristics of environmental protection and super weather resist... |
 |
Polyester based powder coating MT-JA220G White | Product Description MT-JA220G is a polyester based powder coating, formulated using TGIC and is designed for exterior exposure offering excellent ... |
 |
Bonded Metal Powder Coatings for Pipes and Valves | Introduction Bonded metal powder coatings for pipes and valves are specialized coatings designed to provide both aesthetic appeal and functional p... |
 |
(FBE) Single Layer Epoxy Anti-Corrosion Powder Coating/powder coating used in export projects | Product Introduction:This product is carefully formulated using epoxy resin and functional curing agents. It features high reactivity, strong adhes... |
 |
Pure epoxy powder coating | Product model CH Product characteristics Excellent performance, strong versatility, excellent corrosion resistance and electrical insulation. P... |
Same products
 |
5.4,4'-Oxydiphenol CAS 1965-09-9 | 卖方: Yufeng International Group Co., Ltd | Product Name: 4,4'-Oxydiphenol Synonyms: 4,4'-Dihydroxydiphenyl ether 4,4'-Oxydiphenol Bis(4-... |
 |
1,1,2,2-Tetrachloroethane CAS 79-34-5 | 卖方: Yufeng International Group Co., Ltd | Product Name: 1, 1, 2, 2-Tetrachloroethane Synonyms: 79-34-5 s-Tetrachloroethane Acetylene te... |
 |
3.Chlorotrifluoroethylene (CTFE) CAS 79-38-9 | 卖方: Yufeng International Group Co., Ltd | Synonyms: CHLOROTRIFLUOROETHYLENE 79-38-9 CTFE Chlorotrifluoroethene 1-Chloro-1,2,... |
 |
2.1,1,2-Trichloroethane CAS 79-00-5 | 卖方: Yufeng International Group Co., Ltd | Product Name: 1, 1，2-Trichloroethane CAS: 79-00-5 Synonyms:79-00-5, Vinyltrichloride, beta-... |
 |
1.1,1,2,2-Tetrachloroethane CAS 79-34-5 | 卖方: Yufeng International Group Co., Ltd | Product Description Product Name: 1, 1, 2, 2-Tetrachloroethane Synonyms: 79-34-5 s-Te... |
