Powder coating primer containing zinc
Product Description
MT-PZ is a powder coating primer containing zinc which is designed to give enhanced corrosion protection of mild steel. This duplex system combines cathodic protection and barrier effect. Dedicated to steel protection with a surface pre-treatment obtained by grit/shot blasting. MT-PZ is based on a specific epoxy zinc rich formulation that brings conductivity to enable the cathodic protection. MT- PZ includes a specific anticorrosive function which improves the protection in case of scratch. Qualisteelcoat approval: Base Material: Steel PE-0097 2 coat system – up to C4-H, mechanical pretreatment.
Powder Properties
| Chemical type | Thermosetting epoxy |
| Appearance | Smooth |
| Gloss level(60°) | 45-65units |
| Color | Grey (about RAL7012) |
| Recommended Film Thickness (µm) | 70 – 120 µm |
| Density (g/cm3) | 2.1g/cm³ |
| Application | Electrostatic |
| Storage | Under dry, cool (≤ 30°C) conditions |
| Shelf life | 12monthsbelow25°C |
Pretreatment
Surface preparation depends upon the metal, the type of surface, its conditions and the required performance. See our recommendation for pretreatment to be used with MT-PZ.
| Substrate | Mechanical pretreatment | Chemical pretreatment |
| Mild steel | Grit Blasting Sa 2.5 in accordance with ISO NF EN 8501-1. Roughness: Rz 35 60 µm / Ra 6-12 µm | Banned |
| Cast steel | ||
| Electro Zinc steel | Banned | |
| Hot dip galvanized steel | ||
| Zinc sprayed (gas flame/electrical deposition) |
Application
MT-PZ is suitable for corona electrostatic spraying. Tribo application is not recommended.
| Application settings | Fluidizing air pressure: 1.5kg/cm2 initially then 1kg/cm2
Transport air pressure: 0.5 to 0.8 kg/cm Recommended voltage: 65 to 70kV |
| Curing limits | Primer should be cured, or at least gelled, using the recommended curing schedules, before application of the topcoat. The object temperature must not be below 110°C or above 180°C.
The primer should be cured in a convection oven, optionally with infra-red heaters, with air temperature not exceeding 180°C. |
| Recommended film thickness | 70-120 µm A good protection is linked with the recommended film thickness. |
| Recycling | Trials, with suitable recycling equipment, must be carried out before commencing production. Attention should be paid to the ratio of new powder, a minimum of 70% must be used. Gun nozzles must be cleaned every 30 minutes. |
在线联系供应商
Other supplier products
 |
Metal bonding powder | Introduction Accurate selection of powder has always been a problem for the powder industry. To solve this problem, we name the powder according t... |
 |
Epoxy-Polyester Thermosetting Electrostatic Spray Powder Coating | Product Overview Model: MT-062A Yellow powder coating Epoxy-polyester thermosetting electrostatic spray powder coating is a hybrid material combi... |
 |
Metallic flat matte MT-049/96190 | Introduction No. MT-049/96190 Color Metallic color Surface Metallic flat matte System Polyester Scope of applica... |
 |
Aluminum veneer high gloss metal powder coating | Product parameters Name: Powder coating Color: High weather-resistant sand grain brown/high metal matte silver/rose gold Color code: Customized ... |
 |
Polyester based powder coatings MT-620 AM | Product Description MT-620 AM is a series of polyester based powder coatings, formulated without the use of TGIC, designed for the exterior enviro... |
Same products
 |
Easy-cleaning Silicone-Modified Waterborne UV Resin | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | LUV533 is a high-performance, silicone-modified hexafunctional waterborne UV resinengineered to d... |
 |
Water-based Soft-Touch Resin for Consumer Electronics | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | Water-based Soft-Touch Resinis an advanced coating material formulated to deliver a luxurious, ve... |
 |
Conformal Coatings | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | The conformal coatingsprovide good adhesion to metal, PCB and other substrates after curing at ro... |
 |
Metalized & Laser Transfer coating | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | Metallized and laser transfer coatingsare designed with sustainability in mind, ensuring minimal ... |
 |
Hydrophilic coatings for Air Conditioner | 卖方: Guangzhou Human New Material Science and Technology Co., Ltd | A water-based coating combination applied on the surface of aluminum foil, which forms a layer wi... |
