METAL FLANGING
Flanging refers to the stamping process of turning the edge or outer edge of the hole on the workpiece into an upright straight edge with a die. It is included in the forming process of stamping.
WHAT IS THE ADVANTAGE OF METAL FLANGING?
It can process precision stamping parts with complex shape and good rigidity.
Improve the production efficiency. Save dies for some deep drawing parts. Reduce the manufacturing cost.
It can replace the deep drawing work of a complex shape workpiece, so flanging is especially suitable for small batch trial production.
Flanging is usually applied at the edge of the stamping part, which can effectively save the material.
WHAT SHOULD BE CONCERNED IN METAL FLAGGING?
Flanging is a stamping method that turns the workpiece with holes punched in advance into vertical flange along the hole edge. The deformation of hole flanging is from the tensile deformation of the material along the tangential direction, and the closer to the edges, the greater the deformation and the flanged area of workpiece gets thinner. Due to that, the hole edge may be cracked if not dealt properly. In order to prevent the cracking, the flanging degree of the inner hole of the workpiece must not be too large. If the flanging height is large, we can process flanging several times instead.
In flanging, the deformation degree is expressed by cofficient "K", which is the ratio of the aperture before flanging to the aperture after flanging. Obviously, the larger the value of K, the smaller the degree of deformation. On contrary, the smaller the value of K, the greater the degree of deformation, and more likely the edge of the flanging hole will be broken. The minimum value of K occurs with the maximum deformation degree which can be achieved without cracking the hole edge.
In order to prevent edge cracking, K shall not be too small and shall be greater than the minimum value introduced above. Experience shows that the minimum value of K is not only related to the type and performance of the material, but also to the relative thickness of the blank, and the shape of the product.
As a metalworking factory, we can offer sorts of metal work fabricationfor sale, if you are interested, please leave us a message.
在线联系供应商
Other supplier products
 |
MOWER DRIVE ARM IN MOWER DRAG LINK | It is a mechanical assembly used to control the steering of lawn mower drag link, consisting of drive arm, steering arm, steering knuckle, etc. Mos... |
 |
METAL BATTERY BOX | METAL BATTERY BOX It is only the shell of the car battery and is empty inside. We use good quality material and our rich welding experience to m... |
 |
MOWER DECK WHEELS AND BRACKETS | Front forks operate as caster forks that absorb shocks, making drivers more comfortable and improving mower efficiency. It can extend the life of m... |
 |
METAL STAMPING | Stamping is a cold stamping process, which is to cut, bend or shape the material into the finished shape and size in accordance with the mold with ... |
 |
STEERING ARM ADJUSTER IN LAWN MOWER ACTUATOR | Steering arm adjuster is set between drive arm and steering arm elbow, which is consisted of lower adjuster and upper adjuster. It belongs to drive... |
Same products
 |
AAAC (Aluminum Conductor With Profile Wire) | 卖方: 856348 | AAAC (Aluminum Conductor With Profile Wire) Product Overview As a trustedbare conductor supplie... |
 |
LHAJ (Fan Shaped Aluminum Alloy Stranded Wire) | 卖方: 856348 | LHAJ (Fan Shaped Aluminum Alloy Stranded Wire) Product Overview As a professional bare con... |
 |
AACTW (Aluminum Alloy Conductor With Profile Wire) | 卖方: 856348 | AACTW (Aluminum Alloy Conductor With Profile Wire) Product Overview As a professionalbare condu... |
 |
ACSRAS (Aluminium Conductor Aluminium Clad Steel Reinforced) | 卖方: 856348 | ACSRAS (Aluminium Conductor Aluminium Clad Steel Reinforced) Product Overview As a professional... |
 |
AAAC (All Aluminium Alloy Conductors) Product | 卖方: 856348 | AAAC (All Aluminium Alloy Conductors) Product Overview As an experiencedbare conductor supplier... |
