Wire and cable fire resistance testing machine
Meet the standard：
GB/T19216.11-2003/IEC60331-11:1999 "Under flame conditions of cable and optical cable line integrity test Part 11: test device-a flame temperature of not less than 750℃ for individual fire supply" design;
GB/T19216.21-2003/IEC60331-21.1999 "Line integrity test for cables and optical cables under flame conditions - Part 21: Test procedures and requirements - Cables with rated voltage 0.6/1.0KV and below" :GB/T19216.23-2003/IEC60331-23:19 99 "Line integrity test for cables and optical cables under flame conditions-Part 23: Test procedures and requirements-Data cables" :GB/T19216.25-2003/IEC60331-25:1999 "Line integrity test for cables and optical cables under flame conditions-Part 25: Test procedures and requirements-a cable" test standard; At the same time, it meets the standard of GB/T19666-2019 "General Rules for flame retardant and fire-resistant wire and cable"
Technical parameters:
Test station :1 station, one sample at a time.
Test product size: Length {>}1200mm. Length {>}1500mm.
The machine has a total of 5 wire support rings, the test sample will be placed on the wire support ring, and with two measuring fixtures. It is suitable for testing whether the cable or optical cable maintains the integrity of the line when feeding fire at a flame of not less than 750C.
Test wall: The wall is composed of heat-resistant, flame retardant material and is fixed on two horizontal steel beams, one at the upper part of the board and the other at the bottom of the board. The board is about 900mm long, 300mm wide and 9mm thick, and the total weight of the wall (that is, the board plus the supporting frame) is 10±2kg Each steel beam is a square steel pipe with a length of about 1m and 25mm.
If filling material is required, it needs to be placed inside the steel beam. The upper steel beam shall be fixed to the plate so that its upper surface is flush with the upper edge of the plate. The outer edge of each steel beam and plate has a horizontal hole, the exact position of which is determined by the requirements of the specific support liner and support frame.
在线联系供应商
Other supplier products
 |
IULTCS Veslic Leather Abrasion Tester | Introduction This machine is suitable for all types of stain-resistant fur dry and wet rubbing fastness, and various types of fur products and f... |
 |
Automotive Bed Liner Strength Testing Machine | Standard ASTM D624(Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers) ISO 37(Rubber, Vulcan... |
 |
Air Permeability Tester-QINSUN | Air Permeability Tester of textile fabrics complies with ASTM D737. ISO 9237/7231. BS 5636. etc. It is used to test the resistance of the flow of a... |
 |
Car seat fatigue tester | Applicable standards: GB/T 18941-2003"Test method of foam polymer materials for car seats" : This standard specifies the test method of foam pol... |
 |
Suga GX25 | GX25 is designed to artificially reproduce indoor deterioration factors such as sunlight,temperature and humidity.GX25 exposes materials to these... |
Same products
 |
HDPE高速水冷双壁波纹管生产线 | 卖方: Shandong HUASU Plastic Technology Co.,Ltd. | 机头模具采用双流道结构、氮化磨光处理机头，偏壁调整方便快捷，保证内外层壁厚均匀和稳定成型。 最新设计密闭压力水冷冷却结构，冷却充分，多点分布真空系统，效率更高，生产速度更快。 双层在线扩口功... |
 |
PanEVAP & MVR system | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
