Carton Clamp Tester
Product introduction：
This machine mainly aims at the ability of the product to withstand the pressure of
lead from the car when the product is packed in the warehouse or truck, train, etc., so as
to evaluate the damage of the product.
This machine adopts servo motor control, full computer operation, high-grade configuration.
Tests are customized according to ASTM D6055, U.S., SEARS, corporate standards, or
customer specified non-standard requirements.
Compliance Standards:
ASTM D6055
U.S. SEARS
Product Features:
Based on the provided information and typical clamp tester designs:
Servo motor control: Utilizes Japan Panasonic servo motors for precise and dynamic control of clamping plate movement and applied force.
Full computer operation: Enables comprehensive control, programming, data acquisition, and analysis via a computer interface.
High-grade configuration: Implies the use of quality components for reliable performance.
Clamping mechanism: Consists of two parallel splints (clamping plates) that apply horizontal pressure to the test sample.
Adjustable clamping pressure: The pressure applied can be adjusted within a wide range (400 - 3000 Lb).
Adjustable clamping plate height: The height of the clamping plates can be set to accommodate different package heights (0-1000mm adjustment range).
Adjustable speeds: Allows control over lifting speed (10-500mm/min) and clamping speed (10-50mm/min).
Adjustable splint expansion width: The distance between the clamping plates can be adjusted to accommodate different package widths (200-2000mm).
Scope of application：
Applicable to all product packaging testing and verification. The main test is that the
product packaging is subjected to horizontal pressure during transportation and storage
The deformation of the force and the protection ability of the packaging inside the
package, so as to improve the packaging design.
Technical parameter：
Sample shape: parallelepiped transport package
Maximum test weight: 100kg
Clamping pressure: 400——3000Lb（adjustable） pressure can be applied on the
corresponding surface according to the handling diagram on the test sample
Clamping plate surface size: 1100x1100mm（L/W）
Test space size: 1000x1000x1000mm（length, width and height）
Clamping plate height adjustment: 0-1000mm can be set
Lifting speed: 10-500mm/mi adjustable
Clamping speed: 10-50mm/min adjustable
Splint expansion width: 200——2000mm
Transmission mode: Japan Panasonic servo motor （left and right clamps）
Base plate size: 2000x1900mm
Protection device: leakage protection limit device
Cleat requirements: Two gripper plates in the working state （2000 pounds） to ensure
smooth without deformation. The two splints are parallel to each other, and the splints are
vertical to the floor. The thickness of the splint shall not be less than 20mm
Force corrector: With force value display, used to correct the clamping pressure
Force accuracy: national standard 1.6 level
在线联系供应商
Other supplier products
 |
Safety Helmet Electrical Insulation Tester | Product Introduction: Safety hat electrical insulation performance tester used to test the electrical insulation performance of safety hat, high d... |
 |
STD SOLARBOX 1500 - 3000 | Introduction Radiant energy in the STD SOLARBOX is provided by a single superior air-cooled Xenon Lamp generating an irradiance level up to two ... |
 |
Automotive wire cyclic bending testing machine | StandardThis testing machine aligns with global automotive industry standards for wire harness reliability, includingISO 6722(Road vehicles –... |
 |
Car seat center of gravity measuring tester | Main parameters: Measuring range:refers to the maximum and minimum range of the center of gravity of the seat that the tester can measure. This ... |
 |
Building Materials Combustibility Test Chamber | Building materialsfire resistance testis a very importantandprofessionaltestin safety engineering. The national standard, GB/T8626-2007. specifies ... |
Same products
 |
Air Intake Filter Test System | 卖方: Standard Groups | The Air Intake Filter Test System is designed for testing industrial air filters and engine air f... |
 |
Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging | 卖方: Standard International Group (HK) Limited | The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f... |
 |
Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester | 卖方: Standard International Group (HK) Limited | The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter... |
 |
HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ... |
 |
VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine | 卖方: Standard International Group (HK) Limited | The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia... |
