High and low temperature memory impact testing machine

Product Introduction:

Computer controlled memory impact testing machine is mainly used for hard plastics, reinforced nylon, glass steel, ceramics, cast stone, electrical insulation materials and other non-metallic materials impact toughness determination. The testing machine is an ideal test equipment for chemical industry, scientific research units, colleges and universities, quality testing departments, professional manufacturers laboratories and other units. It is a testing instrument with simple structure, convenient operation and accurate and reliable data.

Standards:

1.JB/T 8762-1998 "Plastic Simply supported beam Impact Testing Machine"

2.JJG145-2007 "Verification Regulations of Pendulum Impact Testing Machine"

3.GB3808 "Test of pendulum impact Testing Machine"

4.GB/T 1043.1-2008 "Rigid plastic simple support beam impact test method"

5.ISO 179-1993(E) "Plastics - Determination of impact strength of simply supported beams"

Technical indicators:

1. Impact energy: 2J/4J(simply supported beam); 2.75/5.5J(cantilever)

2. Sampling rate: 10us

3. Resolution: 16 bits

4. Load measurement accuracy: ≤1%

5. Impact knife Angle: 30°

6. Pendulum torque: simple beam 2.1436N.m, 1.0718N.m, 0.5359N.m

7. Cantilever beam 2.9474N.m, 1.4737N.m

8. Pendulum prelift Angle: 150°

9. Simple support beam:

1) Impact speed: 2.9m/s

2) The distance from the center of the pendulum shaft to the center of the sample: 230mm

3) Blade Angle: 30°

4) Blade radius: 2mm

5) Support corner radius: 1mm

6) Front Angle of support: 5°

7) Rear Angle of support: 10°

8) Support span: 40. 60. 70mm

9) Sample type and size (length × width × thickness)mm3:80×10×4mm, 50×6×4mm, 120×15×10mm

10. Cantilever beam:

1) Impact speed: 3.5m/s

2) The distance from the center of the pendulum axis to the center of the sample: 335mm

3) Blade Angle: 75°

4) Blade radius: 0.8mm

5) Front edge Angle: 5°

6) Blade back Angle: 10°

7) Sample type and size (length × width × thickness)mm3:

80×10×4mm

63.5 * 12.7 * 12.7 mm

63.5 * 12.7 * 6.4 mm

63.5 * 12.7 * 3.2 mm

Other supplier products

	High - temperature Pressure Testing Device	Standards ComplianceISO 6722, SAEJ 1128, QC/T 730, GB/T 33549, CQC1103 - 1105 - 2015, etc. Main Configurations 1. Testing device: 2 - station or ...
	Fogging Tester	Standards DIN 75201: Automotive trim material fogging resistance. ISO 6452: Coated fabrics fogging behavior in vehicle interiors. SAE J1756: A...
	AATCC Gray Scale for Color Change	Applicable Standards The AATCC Gray Scale aligns with international colorfastness evaluation protocols, including: AATCC Evaluation Procedure...
	Automotive Wires Dynamic Bending Tester	Standard ISO 6722: Road vehicles – Flexible cables for wiring harnesses. SAE J1128: Low-voltage primary cable for automotive applicatio...
	Car seat component clearance test bench	Applicable standards: Car seat component clearance test benches usually follow the following domestic and international standards: QC/T 805-200...

供应产品

Same products

	Tabletop Xenon Arc Weathering Tester (SunMaster)	卖方: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Water-Cooled Xenon Lamp Weat...
	Blow-By Test Rig	卖方: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com Test system for the characterisa...
	Air filter System（ISO 16890/EN 779）	卖方: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com Filter test system for general a...
	Oil Thread Leak Test System	卖方: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com Test System for oil thread leak ...
	Manual HEPA/ULPA Filter Scanning Test System	卖方: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Manual HEPA/ULPA Filter Scan...