SO2 H2S HCL Corrosion Test Equipment-QINSUN

Meeting Standards:

Carry out various sulfur dioxide gas corrosion tests in accordance with GB10587 - 89. GB2423.9 - 93. GJB150. QC/T417.1 - 2001 and equivalent standards such as IEC, DIN, MIL, ASTM.

IEC 60068-2-42

Environmental Requirements:

1. Power supply: AC380V 3Φ 10KVA 0HZ 2. Allowable voltage range: ±5% of the rated value 3. Maximum load: 6KVA 4. The distance between the chamber and the wall should be greater than 600cm.

Description：

Stainless Steel Noxious Gas Corrosion SO2 H2S CO2 HCL Artificial Climate Chamber:

SO2 HCL H2S Noxious Gas Corrosion Environmental Test Chamber reproduce damages by temperature, relative humidity and noxious gas Corrosion to material, components and constructions.

SO2 HCL H2S Noxious Gas Corrosion Environmental Test Chamber can be used to test t SO2, H2S.

SO2 HCL H2S Noxious Gas Corrosion Environmental Test Chamber can be used for single gas tests.

SO2 HCL H2S Noxious Gas Corrosion Environmental Test Chamber are ranging in size from 100Ltier to 1000Liter.

Structural Materials and Features:

1. The chamber is molded from epoxy fiberglass. Asbestos board is pasted inside the jacket. It is resistant to high temperature and corrosion, lightweight, and has high strength. Both the inner and outer walls of the chamber are smooth and easy to clean.

2. The chamber cover is made of epoxy fiberglass with a top cover temperature of 100 - 200°C to prevent condensed water in the chamber from dripping directly onto the test specimens.

3. Heater: The nickel - chromium alloy heating wire heats from the bottom, forming jacket heating to ensure good temperature uniformity inside the chamber.

4. Humidification method: Humidification by a steam generator.

5. Input methods for sulfur dioxide and hydrogen sulfide: Input from cylinders, and both input and discharge are quantitatively controlled by concentration sensors.

6. Exhaust gas treatment: Install treatment devices for sulfur dioxide and hydrogen sulfide gases. After multi - stage treatment with sodium bicarbonate, the exhaust gas meets the discharge standards (the purification device is external).

Control System:

1. Temperature control: Japanese Fuji temperature controller

2. Temperature input: PT100; Output: Driven by SSR

3. Display range: 0 - 100°C

4. Control range: RT + 5 - 55°C

5. Cycle used (measurement filtering): 2 - 3s

6. The main control components are products from joint - venture companies.

7. The temperature is controlled by a solid - state relay, with stable performance and no noise.

8. A fan is used for stirring and circulation inside the chamber.

9. Display and control of sulfur dioxide concentration

Technical Parameters:

1. Temperature range: 10 - 55°C

2. Temperature fluctuation: ±0.5°C

3. Temperature uniformity: ±2°C

4. Sulfur dioxide gas concentration: 100ppb - 50000ppb (0.1ppm - 50ppm)

5. Hydrogen sulfide gas concentration: 10ppb - 5000ppb (0.01ppm - 5ppm)

6. Relative humidity: 75±3%

7. Tests with sulfur dioxide, hydrogen sulfide, and mixed gases of sulfur dioxide and hydrogen sulfide can be conducted.

Other supplier products

	PLC liquid crystal touch impact testing machine (simple suspension)	Product Introduction: Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinf...
	Vertical Flammability Tester	IntroductionVertical Flammability Chamber for measuring the vertical flame spread for children’ sleepwear, fabrics, other textile materials o...
	Automotive Wires Flammability Tester-QINSUN	Compliance Standards FMVSS 302 (Federal Motor Vehicle Safety Standard) ISO 6722 (Road Vehicle Cable Flammability) UL 94 (Tests for Flammability ...
	Needle Flame Tester	Standard GB/T 5169.5: Electrical & Electronic Equipment – Needle Flame Test Method IEC 60695-11-5/IEC 60695-2-2: Fire Hazard Testing &n...
	Dry Cleaning & Washing Cylinder	Introduction The dry cleaning and washing cylinder consists of a stainless steel rotary test chamber and a multi-speed drive with a digital timer....

供应产品

Same products

	HDPE高速水冷双壁波纹管生产线	卖方: Shandong HUASU Plastic Technology Co.,Ltd.	机头模具采用双流道结构、氮化磨光处理机头，偏壁调整方便快捷，保证内外层壁厚均匀和稳定成型。 最新设计密闭压力水冷冷却结构，冷却充分，多点分布真空系统，效率更高，生产速度更快。 双层在线扩口功...
	PanEVAP & MVR system	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat...
	PanGAP wide gap welded plate heat exchanger	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel...
	PanBloc welded plate heat exchanger	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac...
	PanBox welded plate heat exchanger	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated...