Direcct flame impingement Tester
The testerisdesignedaccording to the BS476-12:1991.Method of test for ignitability of products by direct flame impingement.The accuracy of the tester meets the requirements of relevant standards and meets the control requirements for the accuracy of measurement.
Standards
BS 476-12
Structure
1.Voltage:220V + 10%, 50Hz;
2.Burner.
(1)Ignition source D. A gas burner comprisinga 185 mm long horizontal stainless steeltube(12.0 mm outside diameter, 9.0 mm insidediameter) closed at each end and fitted with acentral gas supply pipe. The burner tube shall havea row of 14 holes of 1.5 mm diameter at 12.5 mmcentres arranged so that the gas jets issue at anangle of 45 below the horizontal.
Theflowmeter shall be calibrated to supply a propanegas flow rate at 25C of 2 l/min
NOTE: Under these conditions the flame height isapproximately 240 mm.
(2)Ignition source E. a gas burner comprisinga 185 mm long horizontal stainless steeltube(12.0 mm outside diameter, 9.0 mm insidediameter)closed at each end and fitted with acentral gas supply pipe. The burner tube shall havea row of 14 holes of 1. 5 mm diameter at 12.5 mmcentres arranged so that the gas jets issue at anangle of 45 below the horizontal.
3.Aburner carriage consisting of a movablecolumn which incorporates a 10 mm On x 1 mmwall stainless steel tube terminated by athreaded boss to which the various burners canbe fixed.
4.A length of 5 mm internal diameter hose not greater than 3.0 m in length to connect the flowmeters to the burner carriage via a gas cock mounted on the carriage.
5.Test frame. A horizontal steel platform to whicha sliding burner carriage and burner tube areattached. At one end of the platform, means shall beprovided to maintain the specimen holder in avertical position.
6.Specimen holder. The vertical specimen holdershall be capable of accommodating the largest size ofspecimen Specimens shall be gripped at intervalsalong both vertical edges.
For narrower specimens, holders may be designed tofit within the widest holder in order to provide acommon position for testing.
7.Burner carriage and tube. The ignition source shall be mounted on a burner support tube fitted to the burner carriage(see Figure 1). The tube shall be equipped with means to allow vertical adjustment of the ignition source position as required by the various tests. The burner carriage shall be designed in such a way that the distance between the burner and the specimen is obtained accurately. reproducibly and automatically and manufactured so that the ignition source can be brought into the prescribed position smoothly and within 1s.
8.A clamp used to fix the soft wood。
9.Draught shields. Draught shields of 9 mm thicknon-combustible board, triangular in shape, with abase of approximately 500 mm andapproximately 750 mm in height shall be providedfor use with ignition sources A. B and C.
在线联系供应商
Other supplier products
 |
byk-gardner scrub abrasion tester | Wet Abrasion Scrub TesterIntroductionThe painted or uncoated surface need use a brush, sponge, scouring pad, sandpaper or other methods to test the... |
 |
Fabric Downproof Tester(Rolling Box) | The Fabric Downproof Tester (Rolling Box) is designed to evaluate the down-proof performance of textiles by simulating friction and impact stresses... |
 |
Fully automatic spinneret mirror inspection instrument (short fiber spinneret) | The Fully Automatic Spinneret Mirror Inspection Instrument (Detector) is designed for automatic inspection of chemical fiber filament spinnerets, s... |
 |
Wool Fineness Analyzer | The Wool Fineness Analyzer measures wool fiber fineness using the airflow method. By forcing air through a measured mass of wool under controlled p... |
 |
Flatbed Ironing Tester - Test Equipment | Product Overview TheFlatbed Ironing Testeris a precision instrument designed to evaluate fabric performance under simulated ironing conditions. It... |
Same products
 |
Air Intake Filter Test System | 卖方: Standard Groups | The Air Intake Filter Test System is designed for testing industrial air filters and engine air f... |
 |
Mattress Spring Fatigue Tester，ASTM D3574 ，how to test mattress for sagging | 卖方: Standard International Group (HK) Limited | The King Size Foam Fatigue Tester is a single-station pneumatic fatigue testing system designed f... |
 |
Mattress Rollator，ASTM F1566 ，Mattress Durability Tester，Mattress Fatigue Tester | 卖方: Standard International Group (HK) Limited | The Mattress Rollator is a laboratory durability testing system designed to evaluate the long-ter... |
 |
HD2 Pneumatic Foam Fatigue Tester，ISO 3385，Foam Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The HD2 Pneumatic Foam Fatigue Tester is a heavy-duty, single-station laboratory testing machine ... |
 |
VW Heel Abrasion Tester，ISO 4649 ，Heel Performance Testing Machine | 卖方: Standard International Group (HK) Limited | The VW Heel Abrasion Tester is designed to evaluate the wear resistance of floor covering materia... |
