Advanced heat insulation test furnace for fireproof coatings

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Application

This test furnace is suitable for determining:

1. Thermal insulation efficiency of steel structure fireproof coatings

2. Fire resistance limit of coated steel components

3. Back-surface temperature rise under standard fire exposure

4. Heating and furnace-pressure stability during fire resistance tests

It is widely used in:

5. Fire protection coating manufacturers

6. Building material testing laboratories

7. National and third-party inspection institutes

8. Research universities and engineering research centers

9. Fireproof material certification and quality evaluation agencies

Standards

This instrument is developed and manufactured in accordance with the following standards:

Primary Standards

GB 14907-2018 – Fire-Resistant Coatings for Steel Structures

GB/T 9978-2008 – Fire-Resistance Tests for Building Construction Elements

International Standards

Although the furnace is primarily based on Chinese national requirements, its fire-curve control and measurement systems align with major global fire-test methodologies, including:

ISO 834 – Standard Fire Resistance Test Curve

EN 13381 Series – Test methods for determining the contribution of fire protection materials to structural elements

ASTM E119 – Standard Test Methods for Fire Tests of Building Construction and Materials

BS 476 (Part 20–24) – Fire tests on building materials and structures

This compatibility allows the furnace to support laboratories that reference or compare international fire-test systems.

Parameters

Item	Specification
Working Voltage	AC 220V ± 10%, 50 Hz
Power Consumption	3 kW
Furnace Pressure Range	0–100 Pa
Pressure Control Accuracy	20 ± 3 Pa
Airflow Range	0–50 m³/min
Airflow Accuracy	≤ ±0.5 m³/min
Fuel Type	0# or −10# diesel
Standard Fire-Curve Temperature Program	60 min: RT–925°C; 120 min: RT–1050°C; 180 min: RT–1115°C; 240 min: RT–1150°C; 300 min: RT–1180°C; 360 min: RT–1210°C
Furnace Temperature Sensors	4 pcs K-type armored thermocouples
Back-Surface Temperature Sensors	2 pcs, accuracy ±4°C
Temperature Control Mode	Average or independent control
Heating Mode	Fully automatic diesel spray burner
Cooling Mode	Automatic exhaust and cooling
Timing Range	0–360 min
Data Storage Capacity	≥100 sets
Sample Size	500 × 500 × 6 mm
Overall Dimensions	1.6 m × 1.6 m × 1.6 m

Test Procedures

1. Cut the sample using a 250mm × 90mm template. If the sample is a melt-shrinkable product, use a 250mm × 180mm template.

2. Clamp the sample in a 250mm × 90mm sample holder, tighten the wing nut, and secure the sample. The sample holder size for melt-shrinkable products is 250mm × 180mm. At this point, do not yet mount the sample holder onto the horizontal rod.

3. Turn on the power switch and set the ignition time to a slightly longer duration, such as 5 minutes. Select the appropriate positioning device according to the ignition method. After pressing "Start Test" and the burner stops at the 45° position, insert one end of the positioning device into the burner. Now mount the sample holder onto the horizontal rod and adjust the sample holder's up, down, left, and right positions to meet the test requirements. Remove the positioning device. Press the return key. After the burner resets, press "Test Reset".

4. Press and hold the ignition button, and simultaneously adjust the flame adjustment valve on the instrument panel. After igniting the gas, adjust the flame height to 20 ± 1mm. When adjusting the flame from large to small, it is easier to first tighten the flame adjustment knob on the panel. The height gauge should be at 20mm. Close the front door.

5. Place two pieces of filter paper in the collection tray and then place it under the sample.

6. Set the ignition time, press "Start Test," and the burner will automatically rotate to the 45° position and remain there for the set ignition time, then reset. The afterglow time starts counting simultaneously. If the sample stops afterglow before reaching the marked line, press "Stop Afterglow." If the sample afterglow reaches the marked line, immediately press "Stop Afterglow." Record the burning time.

7. Press "Test Reset" to stop the test. To continue the test, repeat the above steps; otherwise, turn off the power. Provided by Shandong Provincial Textile Science Research Institute.

Other supplier products

	AATCC KMS-M6 Washer, KMS-M6D Dryer	Whats/App: +86 156 1874 6768 Web: standard-groups.com The AATCC KMS-M6 Washer and KMS-M6D Dryer are precision textile testing instruments designe...
	Ring-on-Block Friction and Wear Test Equipment Model 2M	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards GB/T 3960-2016 Plastics – Determination of Sliding Wear Properties GB/T 3...
	BS 476 non-combustibility test	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com This machine is designed and manfacture according to ISO 1182 .Furnace temper...
	Helmets Vertical SpacingInfrared - positioning Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The helmet vertical spacing infrared positioning tester is a specialized instrument used to...
	Thermal Conductivity Tester for Silicone and Ceramic Substrates，ASTM D5470 industrial and lab material thermal tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com Thermal Conductivity Tester for Silicone and Ceramic Substrates is a high-precision instrum...

供应产品

Same products

	PanEVAP & MVR system	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat...
	PanGAP wide gap welded plate heat exchanger	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel...
	PanBloc welded plate heat exchanger	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac...
	PanBox welded plate heat exchanger	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated...
	PanPHE gasketed plate heat exchangers	卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanPHE gasketed plate heat exchangersare designed with easy access for regular servicing and for ...