Laboratory Drum Reciprocating Wear Test Machine
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Standards
ASTM G133 (Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear)
ISO 7148 (Plain Bearings — Testing of Friction and Wear)
JIS K 7218 (Testing Methods for Plastic Tribological Properties)
JIS P 8139 (Determination of Friction and Wear Properties of Paper and Board)
Parameters
| Parameter | Specification |
|---|---|
| Table size | W 110 mm × L 400 mm |
| Stage travel speed / distance | 30–6000 mm/min / 1–100 mm |
| Operating modes | Single mode, repeat mode |
| Automatic reciprocation count | Max. 9.999.999 cycles |
| Y-axis positioning stage | ±10 mm (reciprocating mode) |
| Drum / roller diameter | Ø10–90 mm |
| Drum fixing method | Dedicated clamping fixtures (customizable by shape) |
| Drum rotation direction / speed | Forward & reverse / 50–500 rpm (custom speeds available) |
| Drum rotation counter | Accumulated up to 9.999.999 cycles |
| Timed automatic stop function | Available, up to 9.999.999 cycles |
| Friction measurement | X, Y, Z directions (Z for vertical load monitoring) |
| Measurement range | Max. 9.8 N for all three directions |
| Vertical load | 1–1000 g (balance arm + weights) |
| 0–10 mm load sensor pressing method (max. 9.8 N) | |
| Pivot vertical movement | 0–150 mm |
| Strain amplifier output | 0–9.8 N = 0–5 V DC analog output |
| Limiter function | Automatic stop at preset friction force in reciprocating mode |
| Measurement position: longitudinal center of sample (drum mode only) | |
| Data analysis (optional) | General friction analysis software for X, Y, Z channels |
Features
Dual-purpose design enables both reciprocating sliding tests and drum rotation tests in a single system
Two loading methods available: traditional weight loading and load-sensor pressing method for drum testing
Real-time monitoring of fluctuating pressing loads during rotation tests
Smooth transition between drum mode and reciprocating sliding mode
Automatic stop function based on preset cycle count or friction force simplifies wear testing
Multi-axis friction measurement provides comprehensive tribological data
Accessories
(1) Sample fixing clamps (customizable upon request)
(2) Ball holder
(3) Blade holder
(4) Flat pressing head
(5) Scratch needle
(6) Weight set: 20 g, 50 g, 100 g, 200 g, 500 g, 1000 g
(7) Power cable
(8) Ground wire
(9) Operating manual
Test Procedures
Select the test mode: reciprocating sliding or drum rotation.
Install the appropriate fixture and securely mount the specimen.
Set the required vertical load using weights or load sensor.
Adjust the travel distance, speed, and cycle count or rotation speed.
Configure automatic stop conditions if required.
Start the test and monitor friction forces in X, Y, and Z directions.
Record and analyze friction and wear data during or after testing.
Maintenance Information
Clean fixtures, drums, and contact components after each test
Periodically inspect moving stages, bearings, and balance arms
Verify load accuracy and sensor performance regularly
Keep the instrument in a clean, dry environment
Calibrate measurement channels according to laboratory schedules
在线联系供应商
Other supplier products
 |
Absorbable Bone - connecting Plates Four - point Bending Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard ASTM F2119: Standard test method for constant load testing of bioabsorbable scr... |
 |
Glove Cut Resistance Test meter | Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Introduction: The machine is used to test the cutting resistance of gloves. Under ... |
 |
Automated material flexibility testing equipment | Whats/App: +86 156 1874 6768 Web: standard-groups.com Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength ... |
 |
DIN 71460 Filter Test System | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application You can use this system for: Quality Control: Verify the performance of fuel ... |
 |
Deval abrasion testing machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Deval Abrasion Testing Machine is designed to measure the wear resistance of stones and... |
Same products
 |
HDPE高速水冷双壁波纹管生产线 | 卖方: Shandong HUASU Plastic Technology Co.,Ltd. | 机头模具采用双流道结构、氮化磨光处理机头，偏壁调整方便快捷，保证内外层壁厚均匀和稳定成型。 最新设计密闭压力水冷冷却结构，冷却充分，多点分布真空系统，效率更高，生产速度更快。 双层在线扩口功... |
 |
PanEVAP & MVR system | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
