Single chip liquid crystal touch impact testing machine
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.
Standards
(1)GB/T 18910.101-2021
(2)IEC 60068-2-75:2014
Main features
Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.
Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.
Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.
Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.
Performance parameters
1. Simple beam impact testing machine
- Impact speed: 2.9m/s
- Impact energy: 1/2/4/5J
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 230mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)
2. Cantilever beam impact testing machine
- Impact speed: 3.5m/s
- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 335mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)
在线联系供应商
Other supplier products
 |
Particle Abrasion Test machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com Industrial Activated Alumina HG/T3927-2007 and other test methods. It is a new generation ... |
 |
Automotive Wires Ozone Aging Chamber | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards ISO 6722: Road vehicles – Electrical cables – Dimensions and test me... |
 |
Cabin Air Filter Test System（Particulate Filtration），Cabin Filter Efficiency Testing System | Whats/App: +86 156 1874 6768 Web: standard-groups.com Test system for testing particle separation of air filters for passenger compartments (DIN ... |
 |
Rubber Test Dummy for Safety Compliance Testing | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application Performance testing of fall protection safety harness systems Performance eva... |
 |
Glove Cut Resistance Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Introduction: The machine is used to test the cutting resistance of gloves. Under ... |
Same products
 |
Laser Cutting Machines | 卖方: Chanxan (Changshu) Laser Technology Co., Ltd. | Laser Cutting Machines PrecisionLaser Cutting Systemsfor Film, Glass & Industrial Materials ... |
 |
Precision Laser Micromachining Machine | 卖方: Chanxan (Changshu) Laser Technology Co., Ltd. | Precision Laser Micromachining Machine| Ultrafast Laser Micromachining Systems Chanxan provides ... |
 |
Ultrafast Laser Systems | 卖方: Chanxan (Changshu) Laser Technology Co., Ltd. | Ultrafast Laser Systems Femtosecond Laser System Ultra-precision femtosecond laser systemfor hi... |
 |
Industrial Laser Equipment Manufacturer | 卖方: Chanxan (Changshu) Laser Technology Co., Ltd. | Industrial Laser Equipment Manufacturer for Precision Cutting, Marking & Micromachining Chan... |
 |
Common Rail Injector Valve F00R J02 012 | 卖方: 868983 | Common Rail Injector Valve F00R J02 012 David Chen |
