ISO 105 X11 ironing sublimation color fastness tester manufacturer
Get a quote：
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Features
Upper and lower heating module independent temperature control
The upper and lower inde pendent temperature control system adopts PID temperature control program, with features of high temperature control precision, low heating overload efficiency, and equipped with PT 100 temperature sensor.
Floating pressurized design
The floating design is carried out when the load is pressurized, allowing the testing of materials of different thicknesses. The pressure distribution and uniform heating can still be ensured in case of testing thicker materials.
Independent temperature control system
The timer is configured to preset the test time. It is automatically start the test timing once the upper platen is pressed downwards, and the buzzer is configured to prompt the test end.
Unique appearance design
The appearance of the tester is exquisite and beautiful. The insulation around the upper and lower heating plates is designed with insulation material to ensure that the heat of the heating plate is not transmitted to the outer casing, which is safe and reliable.
Technical Parameters
|
Test hot plate:W100 X D40mm (same of the upper and lower) |
Tem perature control: independent control of the upper and lower |
|
Heating plate metallurgy: high purity aluminum |
Warming-up time: user-defined |
|
Timer: preset time, automatic timing once the upper plate pressing downwards. |
Applicable test: hot pressing, dry heat, dimensional stability |
|
Heating range: ambient temperature -300°℃ |
Time alarming: buzzing alarm |
|
Hot panel pressure:4±1 KPa(40cm2) |
Weight 25kg |
|
Power:220V 1.6Kwindependent control of the upper and lower |
Power supply: 220V 50Hz |
|
Appearance size:400mmX400mmX450mm |
Test Procedures
First, adjust the working environment to meet JIS L0803 standard conditions: temperature 20±2℃ and relative humidity 65±3%. Acclimatize both the instrument and test samples in this environment for at least 4 hours. Then, cut textile samples into 150mm×50mm pieces (one piece per workstation), ensuring no wrinkles or defects. Finally, check the instrument: confirm it’s connected to the correct power supply (e.g., AC 220V/50Hz) and inspect rubbing heads and workstations for intactness.
Turn on the "Power" button on the control panel. Set test parameters according to relevant JIS standards (e.g., JIS L0849 or JIS K6328): adjust the pressure to 4.9N (the standard value for JIS tests), set the reciprocating speed to 30 cycles/min, and input the required rubbing cycles (e.g., 20 cycles for JIS K6328). Verify all parameters on the digital display to ensure accuracy.
For each workstation, fix the prepared sample flat on the test stage (use clamps to avoid displacement during testing). Attach a JIS L0805 standard white crocking cloth (50mm×50mm) to the bottom of each rubbing head, and secure it tightly with the clamping ring to prevent slipping during friction.
Initiate the TestAfter confirming all samples and components are properly installed, press the "Start" button to begin the test. Monitor the instrument’s operation throughout; if abnormalities occur (e.g., sample shifting, unusual noise), press the "Emergency Stop" button immediately. The instrument will stop automatically once it completes the preset rubbing cycles.
Press the "Stop" button, then carefully remove the crocking cloths and tested samples. Evaluate the results using the JIS L0805 grey scale: grade both the staining of the crocking cloth and the discoloration of the sample (on a scale of 1 to 5. where 5 indicates the best fastness). Record all test details (sample information, set parameters, and evaluated grades) in a test log for future reference.
Turn off the power and disconnect the instrument from the power supply. Wipe the sample stage, rubbing heads, and control panel with a dry, clean cloth to remove debris. Store unused standard crocking cloths in a dry, sealed container, and keep the instrument in a dust-free, dry environment when not in use.
在线联系供应商
Other supplier products
 |
Automatic Textile Fiber Blend Ratio Testing System ISO Certified | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards (1) GB/T 14342-1993: Synthetic short fiber specific resistance tes... |
 |
Racing Seat Headrest Restraint and Front-Rear Impact Testing Machine，Seat headrest restraint and impact test equipment | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Racing Seat Headrest Restraint and Front-Rear Impact Testing Machine is designed to eva... |
 |
Electric rolling wheel peeling testing machine | Whats/App: +86 156 1874 6768 Web: standard-groups.com Electronic pressure roller testing machine (automatic pressure roller machine) specializing... |
 |
ASTM D5865 Oxygen Bomb Calorimeter Manufacturer | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com E-mail：info@standard-groups。com Parameters Powersupplyvoltage ... |
 |
Safety Helmets Impact and Penetration Resistance Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard GB/T 2811-2019(China’s national standard for helmet safety and impact res... |
Same products
 |
HDPE高速水冷双壁波纹管生产线 | 卖方: Shandong HUASU Plastic Technology Co.,Ltd. | 机头模具采用双流道结构、氮化磨光处理机头，偏壁调整方便快捷，保证内外层壁厚均匀和稳定成型。 最新设计密闭压力水冷冷却结构，冷却充分，多点分布真空系统，效率更高，生产速度更快。 双层在线扩口功... |
 |
PanEVAP & MVR system | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
