Mechanical load testing machine for photovoltaic modules
The Mechanical Load Testing Machine for Photovoltaic Modules is engineered to evaluate the mechanical durability of both crystalline and thin-film PV modules under static and dynamic load conditions. By simulating snow, wind, hail, and debris impacts, the system ensures modules meet international mechanical reliability standards. It is suitable for R&D, quality assurance, and certification laboratories.
Application
Static and dynamic mechanical load testing of crystalline PV modules (framed/frameless).
Fatigue testing under pulsating wind or snow load conditions.
Hail and debris impact simulation for module safety evaluation.
Research and development for thin-film PV modules and flexible panels.
Standards
IEC 61215: Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval
IEC 61646: Thin-Film Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval
IEC 62782: Dynamic Mechanical Load Testing for Photovoltaic Modules
UL 1703: Flat-Plate Photovoltaic Modules and Panels
CE Certification (Conformité Européenne)
Features
Multi-Standard Compliance: Simulates forward/reverse loads and dynamic fatigue cycles according to IEC standards.
Ultra-Precise Control: 0.1 N force feedback and ±5% pressure accuracy for reproducible results.
Automated Testing: Programmable cycle counts with AI-assisted real-time crack detection via EL imaging.
Safety First: Dual redundant emergency shutoff, load cell override, and overload protection at 6,000 Pa.
Modular Design: Quick-change fixtures accommodate framed, frameless, and flexible modules; expandable test area up to 3.0m × 2.0m.
User-Friendly Operation: 10” touchscreen HMI with preloaded IEC/UL test sequences and customizable pressure profiles.
Robust Construction: 304 stainless steel frame with epoxy coating ensures long-term durability.
Remote Monitoring & Self-Calibrating: Wi-Fi/Ethernet connectivity and auto-tare/linearity checks before each test.
Parameters
| Parameter | Specification |
|---|---|
| Test Area | 2.8m (L) × 1.8m (D) × 1.95m (H) |
| Forward Load | 5,400 Pa (adjustable) |
| Reverse Load | 2,400 Pa (adjustable) |
| Dynamic Load | 1,000 Pa, 1,000 cycles (7s+3s timing) |
| Pressure Accuracy | ±5% of setpoint |
| Force Sensor | 0.1 N resolution, 10 kN capacity |
| Power Supply | 230V AC, 50/60Hz (single-phase) |
| Air Supply | 6–8 bar (clean/dry air required) |
| Weight | 1,200 kg (net) / 1,500 kg (gross) |
Accessories
Testing Kit: 4x PV module clamping fixtures (adjustable for 16–40 mm frames), 10x load distribution pads (anti-skid rubber)
Software Suite: License key for LoadTest Pro (Windows/Linux), 1-year free access to cloud-based fatigue analysis tools
Calibration & Safety: NIST-traceable pressure gauge, safety harness kit for large modules
Maintenance Kit: Spare O-rings and cylinder seals, machine cleaning solution (non-corrosive)
Documentation: Multilingual quick-start guide (printed + digital)
Test Procedures
Mount PV modules securely on the clamping fixtures.
Select the desired test profile on the touchscreen HMI (forward/reverse load or dynamic cycle).
Set the number of cycles and load parameters according to IEC/UL standards.
Start the test and monitor pressure and force readings in real-time.
Inspect modules after test completion using EL imaging for crack or delamination detection.
Export test data and generate a standardized report for QA or certification purposes.
Maintenance Information
Regularly inspect cylinders, O-rings, and load distribution pads for wear.
Clean the frame and fixtures to prevent dust accumulation.
Verify force sensor calibration periodically using NIST-traceable standards.
Check air supply quality (clean/dry) to ensure consistent pneumatic operation.
Test emergency shutoff and overload protection circuits monthly.
在线联系供应商
Other supplier products
 |
Aerosol Foams Flammability Tester，Automatic Reaction Calorimeter | Product Introduction This product complies with "Recommendations on the Transport of Dangerous Goods - Manual of Tests and Criteria" 31.6 Flammabi... |
 |
Micro Rapid Closed Cup Flash Point Tester(Pensky Martens) | Automatic Flash Point Tester designed for accurate and repeatable determination of the flash point of petroleum products using the Pensky-Martens c... |
 |
Femoral Stem Neck Prostheses Fatigue Testing Machine | Standard YY/T 0809.6 (China): Specifies neck fatigue testing for femoral stems in partial/total hip arthroplasty. ISO 7206-6 (International): Def... |
 |
Diaper Contaminant Detection Machine | Introduction: The diaper impurity detector is used to detect the impurities remaining inside the diaper under a certain strong light irradiation. ... |
 |
Particle Strength Tester | Standard ASTM D4179: Standard Test Method for Single-Pellet Pressure Resistance of Catalysts and Catalyst Carriers ASTM D6175: Standard Test Me... |
Same products
 |
Full-Body Garment Stress Tester,FZ/T 70015 | 卖方: Standard International Group (HK) Limited | TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe... |
 |
Industrial Dry Cleaning Machine,industrial garment steamer | 卖方: Standard International Group (HK) Limited | TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel... |
 |
MST Medical Compression Stocking Tester,compression sock tester | 卖方: Standard International Group (HK) Limited | The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the... |
 |
MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool | 卖方: Standard International Group (HK) Limited | Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi... |
 |
Dental material color stability tester | 卖方: Standard International Group (HK) Limited | Application The applications of color stability testers for dental materials are mainly reflecte... |
