Goggles Puncture Resistance Testing Machine
The safety goggle puncture resistance testing machine is a device used to test the puncture resistance of safety goggles against impact from sharp objects.
Application
It is to make a certain weight of sharp objects fall from the height specified in the standard and act on the surface of helmet or goggles, so as to determine the ability of helmet or goggles to resist penetration by sharp objects.
Standards
GB 811-2010:Helmets for motorcyclists
ECE R22.05:Uniform Provisions Concerning the Approval of Protective Helmets and Their Visors for Drivers and Passengers of Motor Cycles and Mopeds
EN1077:Helmets for alpine skiing and snowboarding
Parameters
| Item | Detail |
|---|---|
| Impact height | 1000mm ~ 3000mm |
| Impact hammer | 3kg, with a cone tip angle of 60 degrees |
| Head fixed frame | Has an adjustable device for rapid and convenient helmet installation |
| Conduit | Adopts high-strength aluminum tube anodic treatment, with a beautiful appearance |
| Hammer lifting method | Manual lifting |
| Impact hammer release device | Electromagnet release device |
| Total height of the instrument | About 5m |
| Voltage | 220V |
Accessoriess
Perforator (puncture cone)
Drop hammer (impact hammer)
Head fixation device (head mold support)
Guide tube
Electromagnetic release device, etc.
Test Procedures
Sample and Equipment Inspection: Confirm that the goggles to be tested are free of manufacturing defects and are properly installed on the corresponding size safety helmet/headgear according to the standard.
Parameter Setting: Select a matching head form, fix the helmet onto the head form, ensuring the goggles are at a natural wearing angle without extra stretching or compression.
Positioning the Punch: Manually adjust the punch position so that it is vertically aligned with the center area of the goggles, and the bottom of the punch is in contact with the surface of the goggles, leaving a space of at least 5mm above the head form.
Performing the Impact Test: Using a manual pull-type or automatic release device, allow the falling weight to drop freely from a set height, impacting the top of the punch, and transferring the impact force to the goggles through the punch.
Data Recording: Record data at the moment of impact using a high-speed camera or pressure sensor, such as the peak impact force and the deformation of the goggles, for subsequent analysis.
在线联系供应商
Other supplier products
 |
Bone Plates Static Four - point Bending Tester | Standard YY/T 0342-2022: Chinese standard specifying methods for determining bending strength and equivalent bending stiffness of straight and pre... |
 |
Leather thickness tester | Product Introduction Leather thickness tester is a special high-precision instrument for leather thickness measurement, which can be widely used f... |
 |
Battery diaphragm permeability tester | Meet the standard: GB/T458. ISO536/2. QB/T1667. GB/T23227. ISO2965. YC/T172. GB/T12655. S05636/3. IS05636/5. GB/T20042.7-2014. GB/T36363-2018. et... |
 |
Direcct flame impingement Tester | Introduction The testerisdesignedaccording to the BS476-12:1991.Method of test for ignitability of products by direct flame impingement.The accu... |
 |
Sauce Packet Pressure Testing Instrument | The pressure resistance tester for sauce packets is a device specifically designed to test the pressure - resistance performance of soft packaging ... |
Same products
 |
Air Permeability Tester STD- F8 | 卖方: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | 卖方: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | 卖方: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | 卖方: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | 卖方: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
