Lamp Anti-aging Test Chamber
Applications:
The machine is used to test the degree of cold resistance for the finished shoes, rubber, plastic, soles, synthetic leather and other materials to understand the material or finished product to adapt to low temperature climate or cold areas, the machine are made of stainless steel and can be installed with a variety of fixture to apply different requirements.
Product Information:
A sample tester manufacture in accordance with ASTMD1148, its function is to simulate the sun's ultraviolet radiation and heat. The tester is exposed to ultraviolet radiation and temperature, after a period of time, observe the degree of anti-yellowing of the sample, with the contaminated gray mark for reference, to determine the degree of yellowing.
Test steps
Turn on the power and set the run time.
Put the test sample into the box tray, positive face up, placed flat, no curl
Press the start button, start the yellowing-test, after the experiment is completed, the alarm alarmed.
After the experiment is completed, remove the sample, wait the sample to be cooled, then put into the standard light box, using D65 light source, observe changes between the sample and untested sample, using GB/T250 color card to rating.
According to the results can be divided into 24/48/96 hours or other specified time, after complete, compare the degree of yellowing; good using contaminated gray scale against yellowing color difference with 1-5 level to determine.
Technical parameters
| Items | Parameters |
| Inner box size | 55 * 50 * 60 |
| Time memory | 0-9999 minutes, electronic display |
| UV light source | lamp tube type 15W, UV lamp 2, UVA340 |
| Standard spare parts | diameter 45cm, a round turntable |
| Rotation speed | 10 ± 2 revolutions per minute |
| Machine size | 114 * 94 * 130cm |
| Manufacturing material | SUS # 304 stainless steel |
| Power supply | AC-220V 50HZ |
在线联系供应商
Other supplier products
 |
Bone Cement Four-Point Bending Fatigue Tester | Standard YY/T 1429 (China): Specifies four-point bending fatigue tests for acrylic resin bone cements under quasi-static and cyclic loading. IS... |
 |
Safety Helmets Impact and Penetration Resistance Tester | Standard GB/T 2811-2019(China’s national standard for helmet safety and impact resistance) GB/T 2812-2006/XXXX(Testing methods for impact a... |
 |
Vehicle Cabin Air Filter Tester | Applicable standards: DIN 71460-1 Road vehicles - Air filters for passenger compartments of motor vehicles - Part 1: particulate matter filtration... |
 |
Shoelace Wicking Tester | Product Introduction: Paste the cut sample on the test fixture of the portable MARK-II anti-slip testing machine, put down the weight of the rotat... |
 |
Lateral Rigidity Tester for Safety Helmets | Lateral Rigidity Tester for Safety Helmets - Material and Parts of Automotive - standard Standards: GB2812 Applications: It is used to te... |
Same products
 |
Thrust Bearing Rolling Friction and Wear Testing Machine | 卖方: Standard International Group (HK) Limited | Applicable Standards: ASTM D3702 ASTM G99 ASTM G77 ISO 18535 Product Advantages: Simulates ... |
 |
Falling Sand Abrasion Test machine | 卖方: Standard International Group (HK) Limited | The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance... |
 |
Conveyor Belt Drum Friction Testing Machine | 卖方: Standard International Group (HK) Limited | Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes... |
 |
Dry Sand Rubber Wheel Wear Tester | 卖方: Standard International Group (HK) Limited | The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater... |
 |
Sliding Bearing Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua... |
