Solar Simulator Tester
The Solar Simulator is a brand-new solar energy simulator that provides a completely new solar energy experience. It features highly realistic sunlight simulation, accurately mimicking the intensity and angle of sunlight at different times and seasons. Through the BBA Solar Simulator, users can experience the warmth and comfort of real sunlight.
Applications
This BBA device provides an environment close to natural sunlight. The purpose of the solar simulator is to provide a controllable indoor experimental facility for testing solar photovoltaic modules. The AAA-grade large-area steady-state solar simulator is primarily used for testing large-area photovoltaic modules, and can perform tests including maximum power testing, temperature coefficient measurement, performance under low irradiance, hot spot durability testing, and photoaging testing.
Standards
IEC 61215: Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval
IEC 61646: Thin-Film Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval
ISO 9060: Solar Energy – Classification of Pyranometers
UL 1703: Safety Standard for Photovoltaic Modules
CE Certification (Conformité Européenne)
Features
BBA-Grade Performance
Class B Spectral Matching: Ensures AM1.5G compliance for accurate energy rating.
Grade B Irradiance Uniformity: <5% deviation across 2.0m × 1.0m test area.
Multi-Mode Testing
STC/NOCT/Hotspot Simulation: Replicates standard test conditions, nominal operating cell temperature, and thermal runaway scenarios.
1.000 W/m² Tuneability: Adjustable irradiance for low-light performance mapping.
Stability First
Class A Transient Stability: <2% flicker during pulsed load testing.
Metal Halide Lamp Longevity: 5.000-hour lifespan with <10% lumen depreciation.
Smart Control
AI-Powered Irradiance Correction: Compensates for lamp aging in real-time.
Remote Calibration: Wi-Fi/Ethernet connectivity for ISO 17025 compliance.
Safety First
UV Filter: Blocks harmful UVC radiation during operator access.
Emergency Shutoff: Dual redundant safety circuits with GPS-enabled alerts.
Technical Parameters
|
Parameter |
Specification |
|
Irradiance Range |
200–1.200 W/m² (AM1.5G filtered) |
|
Spectral Matching |
Class B (IEC 60904-9) |
|
Uniformity |
Grade B (<5% deviation) |
|
Stability |
Class A (<2% transient flicker) |
|
Lamp Type |
Metal Halide (400 nm–1.100 nm output) |
|
Test Area |
2.000mm (W) × 1.000mm (D) |
|
Power Supply |
380V/415V 3-phase, 50/60Hz |
|
Dimensions |
2.500mm (W) × 1.500mm (D) × 2.200mm (H) |
|
Weight |
1.800 kg (net) / 2.500 kg (gross) |
Accessories
Testing Kit:
4x PV module test fixtures (adjustable for frameless/framed modules).
10x Type T thermocouples with ceramic insulation.
Software Suite:
License key forSolarSim Pro(Windows/Linux).
1-year free access to cloud-based PV simulation tools.
Calibration & Safety:
NIST-traceable irradiance meter.
UV safety goggles (Class 1. 3 pairs).
Maintenance Kit:
Spare metal halide lamps and igniters.
Lamp cleaning solution (non-corrosive).
Documentation:
Multilingual quick-start guide (printed + digital).
Compliance certificates for IEC/UL/ISO standards.
Test Procedures
Install PV module securely on the test fixture.
Select appropriate irradiance level and test mode (STC/NOCT/Hotspot).
Configure robotic arm for IV curve tracing and EL imaging positions.
Initiate solar simulator sequence and monitor irradiance, uniformity, and temperature.
Record electrical performance data and export for analysis or certification reporting.
Perform post-test inspection for module integrity and hotspot evaluation.
Maintenance Information
Inspect lamp housings, optical components, and robotic arm before each test session.
Clean lamps, reflectors, and test area to maintain spectral uniformity.
Replace metal halide lamps and igniters periodically according to operating hours.
Verify irradiance calibration with NIST-traceable meter regularly.
Ensure all safety interlocks and UV filters are functional before operation.
在线联系供应商
Other supplier products
 |
Carpet Flammability Tester | Standard BS 4790: Hot Metal Nut Method for Floor Covering Fabrics ISO 6925: Ambient Temperature Tablet Test for Floor Coverings BS 6307: Fire Te... |
 |
Protective Clothing Synthetic Blood Penetration Tester | Introduction It is applicable to the resistance of the protective clothing to the synthetic blood penetration under different levels of test press... |
 |
Helmet Surface Friction Testing Machine | A helmet surface friction testing machine is a device used to test the frictional force between the surface of a helmet and other objects. Its main... |
 |
Protective Clothing Resistance Test device | Related Standards GB/T 22042 - 2008 Clothing - Anti-static Performance - Test Method for Surface Resistivity GB/T 22043 - 2008 Clothing - Anti-st... |
 |
UL94 Horizontal Vertical Flame Tester | Introduction Rubber horizontal vertical flame testeris designed to simulate the early firing situation of electronic and electrical products in ... |
Same products
 |
Falling Sand Abrasion Test machine | 卖方: Standard International Group (HK) Limited | The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance... |
 |
Conveyor Belt Drum Friction Testing Machine | 卖方: Standard International Group (HK) Limited | Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes... |
 |
Dry Sand Rubber Wheel Wear Tester | 卖方: Standard International Group (HK) Limited | The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater... |
 |
Sliding Bearing Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua... |
 |
High temperature vacum friction & wear tester | 卖方: Standard International Group (HK) Limited | The working principle of a high-temperature vacuum friction and wear testing machine is to simula... |
