F-1B Kraft Tape Dispenser

供应商: KUNSHAN BOJIN TRADING CO.,LTD.

供应产品

Operation Video ofF-1B Kraft Tape Dispenser

Before using this machine carefully read the operating instructions. They contain important indications on installation safety, use and maintenance.
Keep this manual with care for any further reference.
It's customer's responsibility to make sure that the personnel who will use the machines read and understand the manual.
The builder cannot be responsible for eventual damage to people deriving from non deservation of the safety norms and the warnings here contained.

This tape dispenser is designed and manufactured only to dispense gummed tape, any different use from that advised is not considered specific. PRINCE PACKAGING will not assume any responsibility following an improper use of the machine.
After unpacking, check the integrity of the machine, in case of doubt does not use the machine and enquire directly to the reseller.
Keep the machine away from children and from personnel who are not authorized or adequated in the use of it.
Follow the instruction manual for machine maintenance.

Before using a new dispenser, wash the moistening brush with cleanser, and rinse it with water.
Insert the brush in the water tank.
Place the lever straight up with your right hand.
Take the water tank with the left hand to the groove in the front of the machine until it touches the back part of the machine.
Lower the water tank till it locks into position.
Let go hold of the feed-in control haulm.

Fill the water through the hole with clean water.
Put a finger on the hole, place the bottle back in its housing, the water will pour from the bottle to the tank.

Adjust the moistening of the tape according to the quality of glue and paper. Increase or decrease the water quantity in the tank, and therefore on paper, raise or lower the lever by placing the water bottle in one of the three different positions in the water tank.(minimal, medium and maximum lever)

Insert the moving plate with the bent part facing up in its housing placed under the white wheel, pushing it ahead.

Rolls of gummed paper can be rolled in two different ways:
With glue facing out the roller should be placed in position A. With glue facing in the roller should be placed in position B.

Adjust roll guide plates to the width of tape and place in their seats. Insert the tape in the guide plates so that the paper comes with the gummed side down, then insert the gummed tape under the moving plate, pushing it all the way. Make sure that the moving plate presser on the tape.

Before removing the bottle, make sure that it doesn't contain water, otherwise cover the filling hole with the finger to avoid outlet of water. Filling the bottle and place it bac in its housing.
AFTER HAVING FOLLOWED THE ABOVED INSTRUCTIONS, THE MACHINE IS READY.
Our machines are safe, repairs have to be made in our assistance centers or by specialized personnel, improper repairs could cause accidents to the user.

	BJ-02E 4 Drivers Wire Cutting Machine	Operation Video ofBJ-02E 4 Drivers Wire Cutting Machine Specification ofBJ-02E 4 Drivers Model: BJ-02E FOUR DRIVERS Power: AC220/ 50HZ 110V/...
	Coaxial Wire Stripping Machine	Operating procedures of semi-automaticcoaxial wire stripping machine. 1. PurposeEstablish proper equipment to prevent accidents and ensure the nor...
	Fully Automatic Terminal Crimping Machine	The operation procedure of Full Automatic Crimping Machine 1. The operator must be trained to post the certificate for working;2. Pre-operation re...
	F-1B Kraft Tape Dispenser	Operation Video ofF-1B Kraft Tape Dispenser Specifications ofF-1B Kraft Tape Dispenser Size: 380300250mm Weight: 9.0kg Available width: 1...
	Tube Cutting Machine	As the advancement of scientific technology, tube cutting machine bring forth the new through the old, with increasing varieties. According to the ...

The Ultimate Tool for Bubble-Free Displays	卖方: 深圳市维客修科技有限公司	FORWARD FW-16R除泡机、FW-8R迷你除泡机，在手机、iPhone、iPad、平板屏幕翻新过程中，去除屏幕OCA气泡，最大支持12.9寸屏幕。安全门设计，24V低压风阀配置，有效降低...
Precision CNC Lathe With Conjoined Oblique Rail Cutter Tower	卖方: Zhejiang Guoyu CNC Machine Tool Co., Ltd.	Technical Characteristics: 45° slant bed base structure, with strict aging treatment, smooth ...
Rail Welder A Frame aligners railway welding tools	卖方: 834406	产品描述 A型车架 A-Frame 是一种导轨对准器，可精确对准要焊接的导轨。该设备在焊接操作期间将导轨固定到位。
2 parts fluid mixing dispenser 2 component dosing epoxy PU silicon rubber vacuum system	卖方: 824681	What is the difference between 2K AB adhesive materials manual potting machine and robot pottingm...
Horizontal Machining Center	卖方: Xilong (Shanghai) Machine Tool Co., Ltd.	Horizontal Machining Center parts can automatically finish four sides milling, boring, drilling, ...