.

Enamel Boiling Water Resistance meter

Whats/App: +86 156 1874 6768

Web: standard-groups.com

Product Introduction:

The enamel layer boiling water weight loss tester is designed according to QB/T 2590-2003 Appendix A, GBT99892-2015 /ISO 28706-2:2008 Determination of chemical attack resistance of enamel Part 2: Resistance to boiling acid, boiling neutral liquid and its vapor chemistry test requirements, and meets the boiling water weight loss test of acidic and alkaline media.

Installation steps:

1. A piece of stainless steel triangle plate is fixed up and down with hexagonal nuts, which is generally fixed when not in use.

2. Put on the rubber washer, and then put on the measured template.

3. Put the washer on, and then put the glass cylinder on.

4. Before the glass cylinder is placed, the heating ring is fixed on the glass cylinder, and the heating ring is fixed at 3-5mm from the bottom of the glass cylinder to avoid touching the rubber ring. At the beginning, observe whether the heating ring is loose (thermal expansion and contraction of the heating ring), if there is, you can adjust some until it does not slide.

5. Then put the rubber ring and white PTFE square plate, if you want to do gas phase erosion, then directly put the template, you do not need to put white PTFE square plate.

6. Then put the stainless steel triangle plate and fix it with the wing nut, and tighten it by turns with even force.

7. Add distilled water to the glass interface to observe whether leakage, leakage, then continue to tighten; If there is no leakage, the test solution can be added according to the standard.

8. Plug in the retarder and connect the graduated condensate collector.

9. Then connect the serpentine condensing pipe, the cooling water enters from the lower end, and the upper end comes out. The condensing pipe is filled with water in the working state, and the water inlet is opened to let the water circulate slowly.

10. After the time is set, press the start button, adjust the voltage regulator to about 175V, and gradually reduce it until the water boils, until it is balanced, and observe that the water droplets of the condensate recycler are between 30 and 50 drops per minute.

11. Please conduct standard test and operate the equipment according to standard technical requirements, pay attention to electrical safety and anti-scald measures, and do not touch the device in the test area during heating.

12. Pay attention to the protection of glass accessories, because it is fragile, please handle gently in the disassembly process!!!

13. After the test is completed, cut off the power supply, turn off the cooling water, pour out the test solution according to the specification, and finally take out the template and weigh it.


在线联系供应商

至: Standard International Group (HK) Limited
Your E-mail:
消息正文:


Send to other suppliers

Other supplier products

Closed - Space Tester for Aerosol Sprays
Closed - Space Tester for Aerosol Sprays Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Description Conforms to UN Recommendations on the Transportation of Dangerous Good...
Hot Tack and Seal Strength Testing Equipment for Flexible Packaging
Hot Tack and Seal Strength Testing Equipment for Flexible Packaging Get a quote: Whats/App: +86 156 1874 6768 Web: standard-groups.com The Hot Tack Tester/Heat Seal Tester is specifically designed for testing the...
AI-powered glass bottle internal pressure resistance tester equipment
AI-powered glass bottle internal pressure resistance tester equipment Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications The internal pressure resistance tester for glass bottles is mainly used to e...
Safety Helmets Impact and Penetration Resistance Tester
Safety Helmets Impact and Penetration Resistance Tester Whats/App: +86 156 1874 6768 Web: standard-groups.com The Safety Helmets Impact and Penetration Resistance Tester is a dual-function testing syst...
Automated syringe plunger force tester
Automated syringe plunger force tester Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications - Quality Control and Supervision The push - force tester for prefilled syrin...
供应产品

Same products

FH-77富氢测试笔
FH-77富氢测试笔 卖方: 科立龙电子股份有限公司 产品说明: 用于测量氢气水(富氢水)和氢气水发生器的溶解氢含量。 特征: 1、电极更换方便 智能、携带方便、操作方便、实用; 产品广泛应用于食品、环卫、地质勘探、冶金、地表水、 ...
Xenon Arc Weather Ometer
Xenon Arc Weather Ometer 卖方: Standard Group (Hong Kong) Limited Get a quote: Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ...
Xenotest | Light Fastness Tester Si220 (SunTest)
Xenotest | Light Fastness Tester Si220 (SunTest) 卖方: Standard Group (Hong Kong) Limited Get a quote: Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ...
Ozone Aging Chamber
Ozone Aging Chamber 卖方: Standard Group (Hong Kong) Limited Get a quote: Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum...
Plastic Smoke Density Tester F313
Plastic Smoke Density Tester F313 卖方: Standard International Group (HK) Limited Whats/App: +86 156 1874 6768 Web: standard-groups.com The F313 Plastic Smoke Density Tester is ...