.

General AC Servo drive can be used with AC servo motor range from 100W~3.8KW

Product Introduction: General AC Servo drive can be used with AC servo motor range from 100W~3.8KW ECON G series servo system(servo drive and servo motor) use the new digital signal processor (DSP) and intelligent power module (IPM), advanced optimization control algorithm can achieve precise control of torque, speed and position, supports CANopen, standard Modbus communication protocol, the servo motor power range is  0.1 kW ~ 3.8kW.Technical Parameter: General AC Servo drive can be used with AC servo motor range from 100W~3.8KWl  Power range: 0.1kW ~ 3.8kWl  Input voltage: single phase or three phase 220VAC (-15~+10%), 50~60HZl  Control mode: position control, speed control, torque controll  Encoder type: 2500 linear incremental optical encoder (provincial line / non provincial line), 1024 wire rotary encoderl  Communication mode: RS485, RS232, CANopen, standard MODBUS communication protocoll  Input and output points: IO can be programmed to support the positive and negative logic settings, 8 input supports 16 kinds of functions can be carried out every function of the function of positioning, 4 output support for 10 kinds of functions which can be carried out in 1 waysl  Operation and display: 5 digital tube, 5 keys, or hand-held operation panell  Monitoring function: to provide position, speed, current, voltage, input and output, and so on up to 30 kinds of state monitoringFeatures:General AC Servo drive can be used with AC servo motor range from 100W~3.8KWl  Using a new digital signal processor (DSP) and intelligent power module (IPM), advanced control algorithm, to achieve high precision control of permanent magnet synchronous motorl  The combination of intelligent PID control algorithm and PDFF controller improves the rapidity and accuracy of position and speed control.l  The notch filter can be used to improve the following performance, reduce the noise and reduce the loss of the machine.l The output signal of the encoder is supported at any frequency dividing ratio, which is more accurate.l  Support load disturbance observer, can carry forward torque and forward compensation, improve dynamic response of the systeml  6 Inertia identification and automatic gain function simplify the debugging process of the system.l  Fan switch temperature can be set, according to the site needs to open air cooling, to provide environmental protection and more cost-effective applicationl  Support debugging software, mechanical characteristics analysis, parameter setting, monitoring and other functions, easy to operatel  The configuration of the hand held operator panel, parameter settings and system debugging is more convenient and quickModelECN-GA3202ECN-GA3204/GA3207ECN-GA3210/GA3215BECN-GA3215BFECN-GA3220BECN-GA3230BRated Output Power100W-200W400W-750W1KW-1.5KW1.5KW-2.3KW2.3KW-3.0KW3.0KW-3.8KWInput powerThree-phase AC220V( -15% to +10%),   50-60HZ / single-phase AC220V (-15% to +10%), 50-60HZEncoder SpecificationIncremental Encoder (2500ppr, 5V)Control Mode1.       Position   Control Mode 2, Pulse Speed Control Mode 3, CAN Control Mode4, 485 Control   Mode 5 and 232 Control Mode2.       1.   Position Control Mode 2, Speed Control Mode 3, CAN Control Mode4, 485 Control   Mode 5 and 232 Control ModeRegenerative BrakeExternalInternal or ExternalInternal   or ExternalControl   CharacteristicsSpeed Frequency Response≥200HZSpeed fluctuation rate:<±3%   (Load fluctuation  0-100%); <±2%   (power -15% to +10%) (at Rated Speed)Speed ratio1:5000Pulse frequency≤500KHzPosition   controlInput mode①    Pulse + direction ② CW pulse +   CCW pulse    ③ A/B quadrature pulseElectronic gear ratiorSetting Range: 1-9999/1-9999Feedback pulseAdjustable according to the number of   encoder wiresFeedback TypeFeedback from incremental pulse   encoder on motor shaftParameter Setting TypeButton on Driver or From the PC Applicable load inertiaLess than 3 times of the motor inertiaRegenerative Brake TypeResistance Consumption BrakeInstallation TypeWall-mounting InstallationGrounding TypeShell grounding: grounding Resistance   ≤0.1ΩMonitoring functionsRotation speed, current position,   command pulse accumulation,  positional   deviation, motor current, command pulse frequency, operating status, input   and output terminal signalProtection functionsOver-speed, main power supply   overvoltage / undervoltage, overcurrent, overload, braking abnormity, encoder   abnormity, position-toleranceDisplay and Operation5-digit LED display panel with 4 keysWorking environmentTemperatureOperation temperature: 0-55℃   / Storage temperature: -20℃ to   80℃HumidityLess than 90% (no condensation)<90%(Non-condensing)Vibration<0.5G(4.9m∕S²) ,   10-60HZ(Non-continuous Operation)Service:General AC Servo drive can be used with AC servo motor range from 100W~3.8KWECON provide technical service from the start to end,and will offer one year warranty. Any problem,can send e-mail to our technical engineer and sales,or directly chat on our website.Payment And Delivery:General AC Servo drive can be used with AC servo motor range from 100W~3.8KWECON supports T/T,Paypal,Western Union to make payment. We can arrange EXPRESS,AIR and SEA shipment,we have professional team to deal with logistic.Recommendations:General AC Servo drive can be used with AC servo motor range from 100W~3.8KWAC Servo Motor Range from 0.1Kw~3.8KwG2 AC Servo Drive Supports Canopen That Makes Fun With Servo System


Send product request

To: Easy Control(Shenzhen) Automation Co.,Ltd
Your E-mail:
Message text:


Send to other suppliers

Other supplier products

Hybrid Servo Drive HS806
Hybrid Servo Drive HS806 Equipped with professional hybrid servo drive hs806 factory, Easy Control (Shenzhen) Automation Co.,Ltd is a leading hybrid servo drive hs806 manuf...
4 Axis Lathe/Turning Controller With PLC---ECN4000TL
4 Axis Lathe/Turning Controller With PLC---ECN4000TL 4 Axis CNC LATHE CONTROLLERBased on ARM9+FPAG large scale CPU and processor ,Website:" TFT display,work with 4Axis lathe machine. This controller s...
4 Axis CNC router controller by hand control
4 Axis CNC router controller by hand control Product Introduction:4 Axis CNC router controller by hand control DSP-A18 is a 4 axis cnc router controller(engraving controller), is professional ...
Stepper Drive DH556
Stepper Drive DH556 Equipped with professional stepper drive dh556 factory, Easy Control (Shenzhen) Automation Co.,Ltd is a leading stepper drive dh556 manufacturer an...
110mm Flange Servo Motor
110mm Flange Servo Motor                       ModelSPEEC110M060DEC110M080CEC110M120DEC110M150DEC110M120CEC110M180DRated Power(WRated Voltage(VRated Current(A)2.53.5564.56R...
All supplier products

Same products

Graphene supercapacitor 2.7V 400F welded farad capacitor
Graphene supercapacitor 2.7V 400F welded farad capacitor Seller: 816692 Capacitance: 400 Farads (F) - This is a measure of the supercapacitor's ability to store elec...
3V Winding Type Super Capacitor
3V Winding Type Super Capacitor Seller: JINZHOU KAIMEI POWER CO.,LTD The Performance Characteristics of 3V Winding Supercapacitor: High energy, high power series ...
2.7V Winding Type Super Capacitor
2.7V Winding Type Super Capacitor Seller: JINZHOU KAIMEI POWER CO.,LTD Why Choose Kamcap Supercaps Supercapacitor is a new type of energy storage device with fast char...
MK Module Supercapacitor
MK Module Supercapacitor Seller: JINZHOU KAIMEI POWER CO.,LTD Performance of MK Module Series Ultracapacitor Kamcap supercapacitor energy storage module with ...
Low ESR Winding Type Super Capacitor
Low ESR Winding Type Super Capacitor Seller: JINZHOU KAIMEI POWER CO.,LTD Low ESR Winding Type Series Performance Characteristics of Low ESR Winding Supercaps Low intern...