2 phase Digital Microstep Stepper Drive with current under 7.2A
Product Introduction:2 phase Digital Microstep Stepper Drive with current under 7.2AECON provides tens of models of stepper drives. From 2 phase to 3 phase, DSP digital, 24--80 DC input or 24--80VAC input, and can provide the right stepper drives to satisfy the special needs of your stepper control systems. ECON’s stepper products are well-known because of their wide choices, excellent performance, easy to use, high reliability, and low cost. The stepper drives have been used by thousands of OEM clients in the world from many of industries such as CNC machinery, medical, electronics, semiconductor, packaging, lab automation.The high performance DH series digital stepper drives are featured with extra low noise, very low motor heating, and ultra smooth motor movements at low speed. With performance and cost balancedDH860 is the new generation high performance fully digital stepper drive which base on 32bit DSP with a advanced algorithm .the power supply range is AC24~80V. it can drive frame 57---110mm 2 phase stepper motor .Ultra low noise and high smoothness at middle/low speed ,and high torque at high speed, which can be applied to different speed control applications. adopt smooth and accurate sinusoidal current vector control technology ,which make motor low heat .Product Features:2 phase Digital Microstep Stepper Drive with current under 7.2A● New generation 32bit DSP ● Good smoothness ,low noise ,low heat ● Build-in micro step setting ● Build-in current setting ● The standstill current can be set to 50%● Oopto-isolated differential pulse input ● The response frequency is up to 300KHz● Over voltage , under voltage, over current protectionApplications It can be used in various kinds of machines ,such as dispenser machine. floating machine3D printer, labelling machine, medical machine, laser cut machine, and so on ,its unique features make it an ideal solution for the applications which require low noise ,low vibration, low heat and high precision Mounting dimension(unit:mm）Product Function:2 phase Digital Microstep Stepper Drive with current under 7.2ACurrent Setting Peak current(A)RMS current (A)SW1SW2SW32.402.00ONONON3.082.57OFFONON3.773.14ONOFFON4.453.71OFFOFFON5.144.28ONONOFF5.834.86OFFONOFF6.525.43ONOFFOFF7.206.00OFFOFFOFFStandstill Current Setting SW4：OFF=Half CurrentON=Full CurrentMicrostep Setting Pul/revSW5SW6SW7SW8200ONONONON400OFFONONON800ONOFFONON1600OFFOFFONON3200ONONOFFON6400OFFONOFFON12800ONOFFOFFON25600OFFOFFOFFON1000ONONONOFF2000OFFONONOFF4000ONOFFONOFF5000OFFOFFONOFF8000ONONOFFOFF10000OFFONOFFOFF20000ONOFFOFFOFF25000OFFOFFOFFOFFInterface Description NameFunctionDescriptionPWRPower light When power on ,the green light is on ALARMOver current/under voltage/over voltage displaying light If the drive Over current/under voltage/over voltage, the red light is on PU+ Pulse input positive Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each falling edge active; 4-5V for High -level, 0-0.5V for low-level Series connect resistors for current-limiting when +12V or +24V used.(should connect 1k resistor for +12V,2k for +24V) PU- Pulse input negativePulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each falling edge active; 4-5V for High -level, 0-0.5V for low-level DR+ Direction input positiveDIR signal: In single-pulse mode, this signal has low/high voltage levels,representing two directions of motor rotation; Series connect resistors for current-limiting when +12V or +24V used.(should connect 1k resistor for +12V,2k for +24V) DR- Direction input negativeDIR signal: In single-pulse mode, this signal has low/high voltage levels,representing two directions of motor rotation; MF+ Enable input positiveEnable signal: This signal is used for enabling/disabling driver. High level for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED). Series connect resistors for current-limiting when +12V or +24V used.(should connect 1k resistor for +12V,2k for +24V) MF- Enable input negativeEnable signal: This signal is used for enabling/disabling driver. High level for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED).AC1AC Power input AC24-80VAC2AC Power inputA+,A-Motor A phase Connect to Motor A phaseB+,B-Motor B phase Connect to Motor B phase!NoteA: Connect power supply rightly ,can’t exceed 80VAC B: If the control signal (PU, DR, MF ) is over 5V ,please connect resistors (at the PU+, DR+, MF+ terminals) for current-limiting.C: If the alarm light is on ,please check it after power off a :the power supply range is 24V—80VAC or not ? b:is there any short on motor wire or others ?Product Service:2 phase Digital Microstep Stepper Drive with current under 7.2AECON provide technical service from start to end,and will offer one year warranty. Any problem,can send e-mail to our technical engineer and sales,or directly chat on our website.Payment and Delivery:2 phase Digital Microstep Stepper Drive with current under 7.2AECON supports T/T,Paypal,Western Union to make payment. We can arrange express,air and sea shipment,we have professional team to deal with logistic.Recommendations:2 phase Digital Microstep Stepper Drive with current under 7.2AStepper Motor Nema 23 SeriesStepper Motor Nema 34 SeriesStepper Motor Nema 42 SeriesPower Supply
Other supplier products
All supplier products
Same products
