AKRON abrasion testing machine
Product Introduction
AKRON wear testing machine is used with the balance, specially testing the wear resistance of rubber products such as soles, tires, car tracks, etc. The counters are electronic automatic, which can set the wear revolution, and automatically stop when the set revolution is reached.
Standard
GB/T 1689 standard, ISO:4661-1:1993. ISO 2481:1988. ISO 471:1983. ISO 1826:1981
Test size
Outer diameter 2 ", inner diameter 1/2 ", thickness 1/2 ", circumference 220mm, hardness 60——70
Machine operation method
1. Prepare the core of the specimen according to the conditions of obtaining the specimen. And record its exact weight.
2. Fix the specimen core on the core shaft seat, and then adjust the Angle of the specimen. (Usually set to 15∘)
3. Different test methods are divided into high standards and low standards according to material requirements.
3.1 High standard requirements:
a. Angle (the Angle between the test piece and the grinding wheel)15∘
b. Load :6 pounds
c. Pre-grinding revolutions :300 revolutions
d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test
e. Install the specimen core and set the wheel rotation times :3000 revolutions
f. After the wear is completed, remove the specimen, brush with a clean brush to remove the powder, and then weigh the accurate weight with a precision balance, which is the weight of the sample after the test
g. Substitute the formula to calculate the grinding amount
3.2 Low standard requirements:
a. Angle (the Angle between the test piece and the grinding wheel)15∘
b. Load :2 pounds
c. Pre-grinding revolutions :200 revolutions
d. Remove the specimen core, brush with a clean brush to remove the powder, then weigh the exact weight with a precision balance, and record the weight of the sample before the test
e. Load back the specimen core and set the wheel rotation times :2000 revolutions
f. After wearing, remove the specimen, brush with a clean brush to remove the powder, and then weigh the exact weight with a precision balance
This is the test weight after the test
g. Substitute the formula to calculate the grinding amount
4. After all specimens have been tested, remove the weight and store it, and remove the debris on the machine.
Wear value calculation method:
Wear (volume m1)== Weight before test - weight after test
Specific gravity algorithm:
a. If the test material is heavier than water
Specific gravity = Weight in air ÷(weight in air - weight of sample in water)
b. If the test material is lighter than water
Specific gravity = weight in air ÷ volume
Technical parameters
Grinding wheel diameter Φ150mm, 40mm(w)， particle size 36#
Grinding wheel speed 34±1r/min
The incline range of the test material is adjustable from 0 to 35°
Test shaft speed (GB)76±2r/min
Load 26.7N±0.2
Counter LED, 0——99.999.999
Volume (W×D×H) 60 × 50 × 45cm
Weight (approx) 60 kg
Power 1 #,AC220V, 50Hz (depending on country or designation)
Send product request
Other supplier products
 |
Automotive connector insertion and withdrawal force testing machine-QINSUN | Standards ISO,CE,UL,ASTM,DIN,EN,GB,BS,JIS,ANSI,TAPPI,AATCC,IEC,VDE Main parameters 1. load: 50kg, 20Kg, 10Kg, 5Kg optional 2. minimum resolut... |
 |
(Ford) Automotive wire flexibility testing machine-QINSUN | Applicable standards: Engineering Specification-Ford Global Wire specificationPART NO. ES-AU5T-1A348-AA Scope of application: Suitable for wir... |
 |
Impact strength tester for car seat launching headrest | Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, which is a key parameter to simulate vehicle collis... |
 |
Schopper Folding Endurance Tester | Use and Scope of application: 1. the instrument is suitable for tensile strength greater than 1.33kn/m, thickness less than 0.25mm paper folding d... |
 |
Automatic cleaning system highway transportation tank car | The STD series automatic cleaning system is suitable for cleaning tank car that transport dangerous chemical products; tank trucks are loaded with ... |
Same products
 |
HDPE High Speed Water Cooled Double Wall Corrugated Pipe Extrusion Line | Seller: Shandong HUASU Plastic Technology Co.,Ltd. | The molds adopt the double flow channel structure and nitriding polishing processed die head. Thi... |
 |
PanEVAP & MVR system | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
