Universal Multifunction Tribology Test Machine
Get a quote：
Whats/App: +86 181 0160 0864
Web: gellowen.co.uk
The Universal Multifunction Tribology Test Machine (UMT Series) is a versatile friction and wear testing system designed for comprehensive tribological evaluation in academic, research, and industrial laboratories. You can perform friction, wear, indentation, and scratch tests on a single platform while obtaining high-precision, repeatable, and reliable data.
The system supports extremely low friction coefficient measurement (down to 0.004) and enables rapid generation of Stribeck curves for in-depth lubricant and material performance analysis. Its modular architecture and interchangeable environmental chambers allow you to adapt the system to a wide range of operating conditions while maintaining compliance with major international testing standards.
Application
You can use this system for a wide variety of tribological and material performance evaluations, including:
Fundamental tribology research and surface performance characterization
Friction and wear testing of lubricating oils and greases
Tribological evaluation of metals, ceramics, polymers, composites, and coatings
Indentation and scratch testing for hardness, elastic modulus, and coating adhesion
Friction and wear testing under high temperature, low temperature, humidity, corrosive, and vacuum environments
Standardized testing in universities, research institutes, and industrial R&D laboratories
Typical tested products include lubricants, bearing materials, surface coatings, engineering plastics, ceramic components, and functional thin films.
Standards
The system is compatible with, but not limited to, the following international standards:
(1) ASTM G77 – Block-on-Ring Wear Testing
(2) ASTM G99 – Pin-on-Disk Wear Testing
(3) ASTM G132 – Ball-on-Three-Plate Wear Testing
(4) ASTM G119 – Reciprocating Sliding Wear Testing
(5) ASTM G203 – Reciprocating Wear of Materials
(6) ASTM G204 – Sliding Wear Under Controlled Conditions
(7) ASTM G206 – Oscillatory Wear Testing
(8) ASTM G133 – Linearly Reciprocating Ball-on-Flat Wear Testing
(9) ASTM G174 – Scratch Testing of Materials
(10) ASTM D3702 / ASTM D3704 / ASTM D2981 / ASTM D2509 – Lubricant and Grease Wear and EP Performance
Parameters
Motion Drive Modules
| Drive Type | Typical Applications | Speed / Frequency Range | Torque / Stroke | Applicable Standards |
|---|---|---|---|---|
| Rotary Drive | Ball-on-disk, pin-on-disk, disk-on-disk | 0.1 – 5,000 rpm | Torque up to 5 Nm | ASTM G99, ASTM G132, ASTM D3702 |
| Reciprocating Drive | Ball-on-flat, pin-on-flat, ring-on-sleeve | 0 – 60 Hz (20 Hz @ 25 mm, 40 Hz @ 12.5 mm, 60 Hz @ 2 mm) | Adjustable stroke | ASTM G119, ASTM G203, ASTM G204, ASTM G206 |
| Block-on-Ring Drive | Block-on-ring wear testing | 0.1 – 5,000 rpm | Torque up to 5 Nm | ASTM G77, ASTM D3704, ASTM D2981 |
| Linear Drive | Scratch, indentation, low-speed friction | 0.002 – 10 mm/s | Stroke up to 120 mm | ASTM G174, ASTM G133 |
Sensors and Measurement System
| Sensor Type | Range / Characteristics |
|---|---|
| 2D Force Sensors | Multiple options, measurement range from 1 mN to 2,000 N |
| Acoustic Emission Sensor | Detection of micro-cracks and friction-induced signals |
| Contact Resistance Sensor | Real-time contact state monitoring |
| Micro-Displacement Sensor | High-resolution displacement measurement for scratch and indentation tests |
Power and Interface
| Item | Specification |
|---|---|
| Power Supply | 220 V, single phase, 50/60 Hz |
| Communication Interface | USB connection |
| Control Computer | Standard PC, freely replaceable |
Send product request
Other supplier products
 |
Fully Automatic Dual-Plate Thermal Conductivity Tester (Guarded Hot Plate Method) | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk Fully Automatic Dual-Plate Thermal Conductivity Tester (Guarded Hot Plate Method) ... |
 |
Falling Sand Abrasion Tester | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The falling sand abrasion tester is used to test the abrasion resistance of coatin... |
 |
Laser Compression Deformation Tester | Get a quote： Whats/App: +86 181 0160 0864 The Laser Compression Deformation Tester for sealing strips is designed for automotive sealing strips t... |
 |
Solid Combustion Rate Tester | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk This product complies with "Recommendations on the Transport of Dangerous Goods - ... |
 |
Textile Thermal Insulation Property Tester | Get a quote： Whats/App: +86 181 0160 0864 The Textile Thermal Insulation Property Tester is designed to evaluate the thermal insulation performan... |
Same products
 |
HDPE High Speed Water Cooled Double Wall Corrugated Pipe Extrusion Line | Seller: Shandong HUASU Plastic Technology Co.,Ltd. | The molds adopt the double flow channel structure and nitriding polishing processed die head. Thi... |
 |
PanEVAP & MVR system | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | Seller: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
