STAINLESS STEEL CNC MACHINING SERVICE

• 

Stainless steel machining chinaservice materials

Stainless steels are often referred to as problem materials in the field of machining. Above all, the great toughness of stainless steels and their tendency to stick is causing difficulties for many users. Stainless steels, for example, are increasingly prone to build-up edge with increasing nickel content. Also important for the assessment of machinability is the chromium content. Stainless steels are divided into three main groups: austentia, ferritic / martensitic and duplex steels. The steels of the first two groups are significantly better to cut than the latter (see Figure 1).

The largest share is held by the austenites; here can again be divided into 4 groups: In optimized for machining so-called "prodec" steels, as they are z. B. Sandvik steel under the trade name "Sanmac" and in normally machined materials, such as 1.4401 or 1.4436. In addition, there are two particularly demanding material classes in machining, the precipitation-hardened stainless steels and the so-called super austenites. On the basis of these criteria, the cut data recommendations of the company Sandvik are then constructed, which additionally distinguishes between rolled and cast stainless steel, since the cast structure is generally significantly worse to machine than the structure of forged or rolled steel.

Turning the easiest

Of the three most important machining processes - turning, drilling and milling - turning is the most unproblematic. For turning stainless steels is usually worked with emulsion as a cooling lubricant. It come to roughing indexable inserts with stable but positively executed chipbreaker geometry, such. As the -MM or -MR geometry used. These insert geometries are used in combination with relatively tough coated carbide grades. Especially for demanding turning operations, eg with severe cutting interruptions, the Sandvik grade GC2035 has proven itself here (see picture 2).

Finishing can be carried out with coated fine and ultra-fine tungsten carbide (GC 1025, GC 2015) or cermet (CT 525) with sharp-edged cutting edges. In order to obtain a controlled chip breaking, inserts with -ML (MóISO-M, L óLight cuts) geometry should be preferred.

Drilling stainless steel materials

Drilling stainless steel materials is much more demanding than turning; This is due to the fact that when drilling due to the process in the center of the tool, the cutting speed is always zero. Accordingly, in the case of drills with indexable inserts, such as the Coromant U drill, a tough carbide grade (GC 1020) should be used in the center. In contrast, a wear-resistant grade (GC3040) can be used as the outer cutting edge. This combination of two different cutting materials makes it possible to optimally adjust the cutting edge stress during machining. For solid carbide drills as well, Sandvik has achieved a unique combination of two carbide grades in a single drill with the TwinGrade GC1030.

When milling stainless steels, especially the strong tendency to built-up edge formation is problematic. If it comes increasingly to the formation of built-up edges, the tool life decreases dramatically. The chips stick to the cutting edge and are pulled into the cut when the cutting edge re-enters the workpiece, and the cutting edge is likely to be damaged. In order to minimize build-up edge build-up as far as possible, positive indexable inserts with a rake angle of at least 20 ° are used. In order to still get stable cutting, particularly tough carbide grades are used. In principle, two machining strategies are possible when milling: it can be run at low cutting speeds and emulsion, or it is worked at high speeds and dry. In the former method, built-up cutting is avoided by using the cooling lubricant and the finished surfaces are slightly better than dry machining, but productivity is low due to the low cutting speed required to achieve acceptable tool life (see Figure 4).

dry milling

When dry milling, the cutting speed is chosen to be much greater, so high that the chips no longer stick to the cutting edge. With the right combination of tool geometry and cutting parameters, most of the heat "goes away" with the chip and the workpiece remains relatively cool. This strategy allows a very high productivity compared to wet processing and is therefore usually much more economical. Sandvik carbide grades GC2030 and GC2040 are particularly suitable for this type of machining.

If the achieved surface qualities are not sufficient for the more economical dry machining, the two methods can also be combined: First, roughing is done with high cutting data without cooling lubricant, but the last cut is made with emulsion and approx. 40% reduced speed. Alternatively, the last cut can also be carried out dry with cermet as cutting material; This is particularly useful when various tools are used for roughing and finishing.

CNC MACHINING PARTS CHINA

Together with 20 years of experience in the manufacturer of machining parts Ningbo Hewchois the professional of finished parts and components.

We can be your reliable partner for turned parts, milled parts, machined parts, cold forged parts, metal stamped parts, special screws, threaded parts or any parts according to drawings, made of aluminum, brass, carbon steel, stainless steel or alloy steel.

Other supplier products

	ALUMINUM CNC MILLING SERVICE	Aluminum milling serviceis one of the numerical control services, which is widely used in the machinery manufacturing, mold processing and so on. B...
	Carbon Steel CNC Milling Parts	Ningbo Hewcho Industrial is an ISO:9001 and ISO/TS16949 certified company dedicated to manufacturing superior-quality Precision turned parts Chinaa...
	CNC Turning Sleeve Bushings	Trade Term: EXW,FOB,CIF.CFR Payment Term: T/T,L/C, Western Union Delivery Time:7-30days Place of Origin: Ningbo, China Information About HEWCHO CN...
	CNC Turning Sleeve Bushings	Basic Info. Trade Term: EXW,FOB,CIF.CFR Payment Term: T/T,L/C, Western Union Delivery Time:7-30days Place of Origin: Ningbo, China Features of our ...
	Aluminum CNC Machining Parts	Aluminum CNC Machining Parts Features: Product name: CNC Machining Aluminum Parts Material: Alumnum Machining Tolerances:0.01mm Machining Pro...

Same products

	Aftermarket Excavator Control Valves	Seller: Colorful tower machinery co ,. ltd	Aftermarket Excavator Control Valves Our are precision-engineered hydraulic components desig...
	Chromium carbide overlay	Seller: JINHUA (QINGDAO) HARDFACING TECHNOLOGY CO., LTD.	Chromium carbide overlay In industries that face severe abrasion and wear, finding effective...
	TILTING CHECK VALVE	Seller: HEBEI LEFLOW IMPORT AND EXPORT CO., LTD.	TILTING CHECK VALVE Valve Size:DN200-DN1200Pressure Rating: PN10/16/25.Design & Manufacture:...
	Porcelain Stay Insulators	Seller: Hebei Yipeng Line Equipment Manufacture Co., Ltd.	Porcelain Stay Insulators , Porcelain Insulators in The Stay Wire Porcelain Stay Insulators...
	Porcelain Line Post Insulators	Seller: Hebei Yipeng Line Equipment Manufacture Co., Ltd.	Porcelain Line Post Insulators Yipeng porcelain line post insulators are produced using a we...