JINDA control panel JDIDL-AN
l. Operation on control panel
2. Set the dial switch l on panel to "Manual", "A" would be indicated for nixie tube status indicated, and set the dial switch 2 to "Forward Operation".
Press "Increasing" or "Decreasing" Key under the manual status, then the actuating mechanism would run normally, mainly observe the on/off direction, feedback current direction, and check whether the limit switches for totally open and close position are running normally, otherwise the changing the wires are needed.
3. 4-20mA Setting: run the actuating mechanism to the totally close position, turn the feedback potentiometer to set the feedback current as 4 mA (nixie tube indicates "∩0" at the very moment), and fix the feedback potentiometer.
4. Press Setting key, waiting until nixie tube indicating "b- -", and then press Setting key for second time with nixie tube indicating "0". Manually operate actuating mechanism to totally open position (indicating "0" in the whole process), then press the Setting key for
the third time, and nixie tube indicates "∩00" soon, then setting 4-20mA completed. Input 4-20mA control signal, set the dial switch to "Auto", nixie tube indicates "A", then can implement auto (romote) control.
- 5. Dead Zone Adjustment (The factory value set is 1.5%, and the adjusting range is 0.5%-5%): the dead zone can be adjusted by pressing "Decreasing" key after "Increasing" key, with zone value increasing or decreasing 0.1% for every pressing, and the the nixie tube indicating the value at the same time. Return to runing staus after several seconds.
6. Forward & Backward Action
The forward action was adjusted in factory. In case of backward action needed by users, operate as below: adjust as forward action, then adjust the dial switch to "Backward Operation".
7. Use Method of Infrared Remote Controller
Setting the on-off dial switch l on panel to Auto, remote controller can be adopted for operation. When the remote controller is set in "Auto", the "Manual-Auto" operation can be selected for dial on control panel. Note: When set the dial switch to "Manual" status, A/M key losses its function, and can only be operated manually.
When set the dial switch to "Auto" state, the method for setting 4 - 20 mA with remote controller is same as the above procedures.
The "Manual" state was set for dial switch in factory.
Malfunction: Set the dial switch on control panel to "Auto", however, the actuating mechanism can only be adjusted manually, not automatically.
Solution: Check nixie tube display, and set A/M key on remote controller to "A" in case of status indicated as "∩" (manual).
Send product request
Other supplier products
 |
ZJHP/M pneumatic diaphragm regulating valve | The ZJHP/M pneumatic diaphragm regulating valve consists of a multi-spring pneumatic diaphragm actuator and a low flow resistance fine regulating v... |
 |
SD electric ball valve | SD electric ball valve used for cutting off or connecting mediuminside the pipeline and can be also used for adjusting and controlling the fluid. I... |
 |
Multi Turn on-off electric actuator DZW | Overview DZWmulti-turn smallelectric valve actuator is a new product that extends from small-diameter gate valve and globe valve. It changed t... |
 |
Bernard control panel GAMX-2007 | ♦Input signal is 4~20mA or Passive switch signal(without external contact withthe power signal).output signal is 4~20mA, Complete isolation b... |
 |
Exquisite Small Type Electric Ball Valve Actuator | Electric flanged ball valve has the advantage of powerful operating function, small volume, light weight, beautiful outlook, wear-resisting, simple... |
Same products
 |
API Standard Flange Swing Check Valve | Seller: Wenzhou Chenyu Valve Co., Ltd | Flange Swing Check Valveis a specific and widely used type of Check Valve. Its primary function i... |
 |
Triple Eccentric Flange Butterfly Valve | Seller: Wenzhou Chenyu Valve Co., Ltd | The triple eccentric flange butterfly valvehas three eccentricities. The first eccentric shaft de... |
 |
Casting Trunnion Ball Valve | Seller: Wenzhou Chenyu Valve Co., Ltd | Cast steel trunnion-mounted ball valvesfeature a split body design and can be customized or autom... |
 |
Aftermarket Excavator Control Valves | Seller: Colorful tower machinery co ,. ltd | Aftermarket Excavator Control Valves Our are precision-engineered hydraulic components desig... |
 |
TILTING CHECK VALVE | Seller: HEBEI LEFLOW IMPORT AND EXPORT CO., LTD. | TILTING CHECK VALVE Valve Size:DN200-DN1200Pressure Rating: PN10/16/25.Design & Manufacture:... |
