Toilet Corrosion Test Chamber (HCl and Ammonia)
Product Description:
Toilet seat hydrochloric acid and ammonia corrosion tester is used for testing to evaluate the ability of toilet seat products to provide adequate rust protection against detergents and urine. The test chamber by simulating ammonia components, hydrochloric acid solvent body, medium on the toilet electrical components or other inorganic cover layer in condensation conditions of corrosion test. The test chamber is electronic toilet sampling and testing of product quality supervision and inspection institute 3 testing organizations and toilet manufacturers of essential test equipment.
Conformity with standards:
GB/T 4706.53-2024
IEC 60335-2-84:2019
The conformity of the tested samples of toilet bowls is checked by the following tests:
The following tests are carried out on the samples of the toilet bowls, except for the case where the electrical components are closed or where it is not possible for them to be exposed to contaminated environments. The toilet samples shall be exposed to ammonia gas volume fraction of (0.055% by 0.005%) at room air pressure for 96 h. Then the toilet samples shall be exposed to hydrochloric acid volume fraction of (0.0005% by 0.0002%) at room air pressure for 96 h. The toilet samples shall not show any damages that lead to the non-compliance with the requirements of the GB/T 4706.53-2024 standard after the test.
Main parameters:
1. Inner box size: W1200×H1200×D1200mm
2. Outer box size: about W2350×H1700×D1500mm
3. Test temperature: room temperature
4. Ammonia concentration: 0.055%±0.005
5. Hydrochloric acid concentration: 0.0005%±0.0002
6. Test gas generation method: cylinder method
7. Test gas control: according to the test requirements using the volume ratio calculation, and then use the anticorrosive mass flow meter to control the flow rate
8. Sample test frame: Maximum load ≥50kg; placed vertically at 90°±2°.
9. Use of the environment and temperature: must be a clean room, no strong airflow, temperature 25 ℃ ± 2 ℃
10. Use of environmental humidity: <75% RH
11. Equipment power supply: AC 220V 50/60Hz
12. Installed power: 400W
Equipment equipped with:
1. Hydrochloric acid and ammonia corrosion test chamber 1 set
2. A set of exhaust gas filtering device
3. ammonia gas cylinder 1 bottle
4. Matching special pressure reducing valve 1pc
5.1 bottle of hydrochloric acid
Send product request
Other supplier products
 |
Pipes Hydrostatic Testing Machine | Standard ISO 1167: For thermoplastics pipe systems under constant internal pressure. ASTM D 1598: Standard test method for time-to-failure of pla... |
 |
Mask Leakage Tester | Mask Leakage Tester - Non-woven and Geomembrane - standard Applications: The Mask Integrity Test Accessory (MITA) works in tandem with the CBRN... |
 |
Ink printing durability test machine | Product Usage: Printing ink Decolorization test machine, also known as abrasion tester, friction tester, etc., mainly for printing ink for printed... |
 |
20L Spherical Explosion Tester | The 20L Spherical Explosion Tester is a state-of-the-art laboratory instrument designed for the precise evaluation of the explosion characteristics... |
 |
DeMessia zigzag tester | Compliance Standards IEC 60695-2-1 (Fire hazard testing) ISO 6722 (Road vehicles - 60 V and 600 V single-core cables) ASTM D5422 (Standard Test ... |
Same products
 |
Air Permeability Tester STD- F8 | Seller: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Seller: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Seller: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Seller: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Seller: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
