Metal Wire Repeated Bending Tester
Main uses:
Metal wire repeated bending tester used for repeated bending test of wire, for different specifications of wire bending radius can be replaced with different round rod, bending position （height） can be adjusted, perforation diameter to replace different bushings.
Test principle:
The sample of a certain diameter is clamped in two round rods of specified size, press the button, the sample is bent at about 90°, the sample is broken, and the bending number is automatically stopped, and the bending number is recorded to test the performance of the metal wire under plastic deformation and the defects displayed during repeated bending.
Meet the standard:
GB/T 238-2013 "Metal material wire repeated bending test method"
GB/T 235 "Metal material thickness is less than or equal to 3mm sheet and thin strip repeated test method"
ISO/DIS 7801-1983 "Repeated bending test of metal wire"
Product Advantages:
Evaluates Bending Fatigue: Directly assesses the wire's resistance to repeated bending stress.
Quantifies Ductility: Provides a numerical value (number of bends to failure) for wire ductility under dynamic bending.
Detects Defects: Repeated bending can reveal hidden surface or internal defects that may lead to premature failure.
Standardized Testing: Enables testing according to established national and international standards.
Controlled Test Parameters: Ensures repeatable and comparable test results through precise control of bending angle, speed, and radius.
Automated Operation: Automatic stopping upon fracture and cycle counting simplify the testing process.
Versatile: Can test a range of wire diameters and allows for adjustment of test parameters.
Main parameters:
1, sample diameter: 0.3——6mm or 4——10mm
2, sample length: 150——200mm
3, bending Angle: left and right bending 90 degrees
4. Bending speed: 60 times/min
5. Counting range: 0-9999 times
6. Motor power: 1.1KW
Send product request
Other supplier products
 |
Wet Penetration Tester | Application: Protective Clothing Tester Wet Microorganism Bacterial Penetration Resistance Tester Apparatus: used to measure the penetration perfo... |
 |
Chin Strap Testing Machine | Standard GB/T 2812-2006: Safety Helmets GB/T 2811-2019: Head Protection – Vocabulary and Test Methods Equivalent Compliance: ISO/EN 397 ... |
 |
Helmet Goggles High Speed Particle Impact Testing Machine | Main Purpose To test the impact - resistance performance of glasses, goggles and face shields at a certain speed. Applicable Standards SNELL SA/... |
 |
Bone Plates Four Point Bending Fatigue Tester | Standard YY/T 1503-2016: Chinese standard specifying test methods for bending fatigue properties of metallic bone plates, requiring 1 million cy... |
 |
Mask Breathing resistance testing machine EN149-2009 section 7.15 EN 13274-3 | Standards: EN149-2009 section 7.15. 8.3.4. EN 13274-3. GB 19083. GB 2626. NIOSH 42 CFR Part 84. JIS/T 8151 Mask Breathing resistance testing mach... |
Same products
 |
Air Permeability Tester STD- F8 | Seller: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Seller: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Seller: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Seller: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Seller: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
