KES - FB2 - S Bending Tester
Compliance Standards
ASTM D790 (Plastics Flexural Properties)
ISO 178 (Flexural Strength of Rigid Plastics)
SAE J2748 (Automotive Composite Flexure)
IEC 62133-2 (Battery Module Bending)
EN 1170-5 (GRC Flexural Testing)
Technical Parameters
| Parameter | Specification |
|---|---|
| Force Range | 0.1N - 2000N (±0.5%) |
| Deflection Accuracy | ±1μm @ 10mm span |
| Test Speed | 0.1 - 500 mm/min |
| Support Spans | 10-500mm (adjustable) |
| Bending Radius | 0.5-100mm (±0.01mm) |
| Angular Resolution | 0.01° |
Key Features
3-point & 4-point bending configurations
Real-time curvature measurement system
Automatic neutral axis calculation
High-speed strain mapping (1000 fps)
Multi-stage bend/reverse bend cycles
Test Capabilities
| Test Type | Standard | Parameters |
|---|---|---|
| Flexural Modulus | ASTM D790 | 2% strain limit |
| Bending Fatigue | ISO 12106 | 10⁷ cycles @ 20Hz |
| Springback Analysis | SAE J2748 | 180° bend + release |
Measurement System
- Dual-axis load cell (Fz + Mx)
- Laser-based deflection tracking
- Surface strain mapping via DIC
- Real-time moment-curvature plots
Standard Configuration
- Stiffness-rated frame (100kN/m)
- Interchangeable rollers (R1-R50mm)
- TestXpert III analysis software
- 2000N capacity load cell
Automotive Options
- Battery pack torsion simulation
- Seat structure cyclic loading
- Door seal compression-bend
- Thermal cycling (-40°C to 150°C)
Safety Systems
- Over-moment protection
- Emergency roller retraction
- Specimen ejection detection
- Automatic force dump circuit
Implementation Notes
- Calibrate per ISO 5893 (Roller alignment)
- Maintain 40-60% RH for polymer tests
- Use alignment jig for multi-layer stacks
- Ground isolation for electronic components
Implementation Notes
- Calibrate per ISO 5893 (Roller alignment)
- Maintain 40-60% RH for polymer tests
- Use alignment jig for multi-layer stacks
- Ground isolation for electronic components
Send product request
Other supplier products
 |
Fire stability tester for paper gypsum board | Fire stability tester for paper gypsum board - Other test instrument - standard Product Information: Technical parameters: 1, combustion tempera... |
 |
Surface Resistance Tester | Surface Resistance Tester - Textile and Apparel - standard Standards: GB/T 22042-2008 Garment. Anti-electrostatic property. Surface resistivity... |
 |
Spring torsion tester | Main uses: Spring torsion testing machine is suitable for all kinds of large spring torsion Angle, torsion moment test, add the corresponding acce... |
 |
Helmets Acceleration Impact & Penetration Tester | Standard GB/T 2812: Safety Helmets (China National Standard) Equivalent Compliance: ISO 6220-1 (Industrial Safety Helmets – Impact Absorp... |
 |
Sliding Bearing PV Tester | Standard This machine is mainly applicable to GB 7948-1987 plastic bearing limit PV test method, JB/T 7381-2010 powder metallurgy oil bearing PV v... |
Same products
 |
Air Permeability Tester STD- F8 | Seller: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | Seller: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | Seller: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | Seller: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | Seller: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
