Minimum ignition point test machine,Automated dust cloud ignition tester,IEC 61241
Introduction
This machineis a way of testing the sensitivity of the ignition that the dust cloud is in the heated environment. When a lot of dust is exposed in heating the air and the air temperature is high enough, it may lead to spontaneous combustion. This method can test the minimum ignition temperature of combustible dust cloud.
Standard
IEC 61241-2-1:1994.EN 50281-2-1:1999.
Technical parameters
1. The Test is carried on the in Godbert-Greenwald furnace.
2. Theheating furnace is consist of the vertical quartz tubes . The hole is at the bottom of the tube.
3. Furnace operating temperature range: room temperature ~ 800 ºC
4.The operating temperature can rise to 1000 ºC to cleanthe test chamber .
5. Temperature accuracy: ± 1% (higher than 500 ºC), ± 3% (lower than 300 ºC).
6. The pressure of the dispersion air chamber: 0 ~ 1 bar
7. The pressure accuracy of the air storage device : ± 5%
8. Size : 500X300X450 mm.
9. Power: 230v / 50Hz or 110v / 60Hz.
Testing process
The Test is carried on the in Godbert-Greenwald furnace. The heating furnace is consist of the vertical quartz tubes . The hole is at the bottom of the tube.the glass observing room is connected with sample fixing device at the top of the quartz tubes. The compressed air from the tank blows the dust into the heating furnace and the sample fixing device ,and then exposed into the glass observing room and the quartz tubes .the heating furnace is located on the holder . And you can observe the ignition appearance from the bottom of the furnace. The test begins from the 500ºC. If you observe the ignition appearance ,you shall decrease the temperature at the 10ºC,until the ignition does not appear.
Results description
When the ignition occurs , the lowest temperature is recorded as the minimum ignition temperature of the dust cloud .
The minimum ignition temperature of the test data information is used to determine whether the surface temperature of the equipment can cause the automatic fire of the exposed dust . It is an important standard to evaluate the selection of the equipment at the condition of the dusty environment . When using the minimum ignition temperature testing data ,you shall leave a safety limit for the small-scale test .
Send product request
Other supplier products
 |
fabric wet adhesion performance tester | Product Overview The Fabric Wet Adhesion Performance Tester is a precision instrument designed to evaluate the adhesion behavior of clothing fab... |
 |
zipper reciprocating fatigue testing machine | Application The instrument is widely used to evaluate the durability and service life of zippers with various length in the fields of clothing acc... |
 |
Motor Accessories Combustion Chamber,FMVSS 302; ISO 3795; ASTM D5132-04 | Introduction: This machine is designed according to ISO3795 standards and relevant clauses. Apply to identify vehicles (cars, multipurpose passeng... |
 |
Torque - to - Failure Tester | Standard YY/T 0662-2008(Chinese standard for orthopedic implant testing) ISO 5832-1(Metallic materials for surgical implants – Wrought stai... |
 |
Adiabatic Accelerated Calorimeter | Product Description Adiabatic Accelerated Calorimeter determines the thermal behavior of samples under adiabatic conditions by keeping the tempera... |
Same products
 |
Test for Flammability of Materials ,AS1530.2,Fire reaction test apparatus | Seller: Standard International Group (HK) Limited | Introduction Thistester is developed base on thestandard AS1530.2. test for flammability of mate... |
 |
Building Material Radiant Panel Test Machine,AS/NZS 1530.3 | Seller: Standard International Group (HK) Limited | Products This machine is designed according to AS/NZS 1530.3; Thedeviceviaagasradiantplatetohea... |
 |
Radiant Panel Flame Spread Apparatus，fire spread test machine | Seller: Standard International Group (HK) Limited | Description ASTM E162 is one most widely used test standard to evaluate the propagation properti... |
 |
Single-Flame Source Tester， ISO11925-2，DIN 53438; DIN4102-1 | Seller: Standard International Group (HK) Limited | Introduction This instrument is designed according to ISO11925-2. it is used to test building ma... |
 |
Density of Smoke from the Burning or Decomposition of Plastics，ASTM D2843 Smoke Density Test | Seller: Standard International Group (HK) Limited | Introduction In a fire, people are often smoke suffocated or unable to escape because of the inv... |
