Automatic Spring Separator

• 

The application and maintenance of spring separator:

(1) Adjustment of spring external diameter:

Mainly when adjusting the spring external diameter mechanism, roll cylindrical spring, it only needs to debug the plunger inside or outside, don't need a device variable diameter CAM, convex type in the conical spring, spring, variable diameter CAM must be equipped.
A. Grinding of the core axis:
For the double pole

spring separator

, the outer diameter of the dabber should be smaller than the inner diameter of the spring, but it should not be too small. Otherwise, the spring will shrivel when it is cut off. Meanwhile, the clearance between the cutter and the dabber should not be too large.
B. Adjustment of the mandril:
The mandril is to control the diameter of the spring, and the diameter of the spring is smaller when the top mandril is moving in the direction of the core axis, while the other side is larger, and the diameter of the lower tip is larger in the direction of the core axis, while the other is smaller.

(2) Adjustment of feeding length and total winding number:

Feed length depends on the selection of gear teeth and the number of teeth on the gears (Z) = spring on the length (mm)/feed coefficient of spring on the length (L) = (spring snap - wire diameter) * ∏ * total number of turns.
After obtaining the gear of the desired gear, mounting the flange, the required total winding number can be obtained.

(3) Adjustment of free height, pitch and effective winding number:

The free height and pitch are adjusted by adjusting bolts under the pitch knife. Adjust the screw downward, shorten the height and shorten the pitch. On the contrary, the length, pitch and effective winding number are adjusted by the variable distance CAM. The larger the working face of the CAM is, the larger the effective circle increases, and vice versa.

(4) Adjustment of supporting ring and tightening force:

When rolling the compressing spring, it is necessary to tighten the ring at both ends and have a certain requirement for the length of the tension. Otherwise, it will affect the working characteristic of spring, and tight position also requires a certain tension in case of the end gap. It is also required that the rings are not allowed to have clearance in the rolling spring with initial tension. Both of these conditions need to be adjusted and tightened around the area.

Other supplier products

	Label Cutting Machine	Description ofLabel Cutting Machine With Cold & Hot Cutting BJ-07N Model: BJ-07N with Memory Knife: Hot & Cold cutting CUT LENGTH (mm)...
	Pneumatic Terminal Crimping Machine	Pneumatic Terminal Crimping Machine Cable Hydraulic Crimping Machine BJ-30T * Force:20Ton* Applicable Scope:1-200mm² wire* Strok...
	Enameled Wire Stripping Machine	Installation and use of . Choose appropriate peeling wheel and install them on the machine. Put two enameled wire in the middle of the peeling whe...
	MS-1100 Electronic Tape Dispenser	Specifications ofMS-1100 Electronic Tape Dispenser Safety guard system prevents activation of cutter when foreign objects are present Will incr...
	Coaxial Wire Stripping Machine	Operating procedures of semi-automaticcoaxial wire stripping machine. 1. PurposeEstablish proper equipment to prevent accidents and ensure the nor...

Same products

	The Ultimate Tool for Bubble-Free Displays	Seller: Shenzhen Wikshu Technology Co.	FORWARD FW-16R Bubble Remover and FW-8R Mini Bubble Removal Machine removes screen OCA bubbles du...
	Precision CNC Lathe With Conjoined Oblique Rail Cutter Tower	Seller: Zhejiang Guoyu CNC Machine Tool Co., Ltd.	Technical Characteristics: 45° slant bed base structure, with strict aging treatment, smooth ...
	Rail Welder A Frame aligners railway welding tools	Seller: 834406	产品描述 A型车架 A-Frame 是一种导轨对准器，可精确对准要焊接的导轨。该设备在焊接操作期间将导轨固定到位。
	2 parts fluid mixing dispenser 2 component dosing epoxy PU silicon rubber vacuum system	Seller: 824681	What is the difference between 2K AB adhesive materials manual potting machine and robot pottingm...
	Horizontal Machining Center	Seller: Xilong (Shanghai) Machine Tool Co., Ltd.	Horizontal Machining Center parts can automatically finish four sides milling, boring, drilling, ...