Thermal Protective Performance Tester (TPP)
Standards：
BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306
Feature：
Industrial personal computer with analysis software is suitable for severe testing conditions.
Automatic calculation for heat transmission factor and radiant heat transfer index.
Sample holder with force applied kit is easy to operate.
Single pump for shutter movement and cooling water loop.
TPP Specifications：
• Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size
• Copper slug calorimeter sensors (ASTM or ISO)
• ± 0.75°C temperature measurement
• ± 3% radiant heat flux measurement
• Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm)
• Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm)
• Power Requirements: 208-265 VAC, 50/60Hz, Single-phase
• Maximum nominal current 20 Amps
• Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max)
• Cooling Water: Cooling water required, chiller or tap water source is acceptable
• Propane Requirement: Regulated supply at 15 PSI (minimum)
• Water-cooled radiant heat source with 9 quartz (500W) infrared lamps
• Two gas burners with flame detection auto ignition
• Mass flow controller for precise gas control
• Water-cooled protective shutter
• Pneumatic sample carriage and shutter assembly
• Integrated sensor cooling stand (air cooled)
• Emergency stop cuts gas flow, power to lamps and pneumatics
• Tinted tempered glass shield protects operator
• Software safety interlocks monitor water flow, carriage position, burner ignition
Send product request
Other supplier products
 |
Thrust Bearing Rolling Friction and Wear Testing Machine | Applicable Standards: ASTM D3702 ASTM G99 ASTM G77 ISO 18535 Product Advantages: Simulates Real-World Conditions: Allows testing under cont... |
 |
Test for Flammability of Materials | Introduction Thistester is developed base on thestandard AS1530.2. test for flammability of materials. The method is applied to the testing of a t... |
 |
Flammability Tester STD-CFR 1610 | Product Introduction Model:STD-CFR 1610 Standards ASTMD 1230 ASTM F 963 ASTM F2100 -16 CFR PART 1610 Features 1.Stainless steel cabnet, beauti... |
 |
International rubber hardness tester | Technical parameters: 1, hardness effective measurement range: 30-95IRHD 2, initial load （contact force） : 8.3±0.5mN 3, the main load （pr... |
 |
Smoke - Emission Testing Machine for Aerospace Wires and Cables | Standards Compliance: U.S. Military Specifications: MIL-W-5086C & MIL-W-22759D (smoke density and toxicity limits for wiring). Chinese Nati... |
Same products
 |
Custom Stainless Components for OEM Applications | Seller: Yongjia County Yaokang Technology Co., Ltd. | Our stainless steel float balls are designed for float valves, water tanks, and industrial liquid... |
 |
Precision Design for Automatic Liquid Level Control | Seller: Yongjia County Yaokang Technology Co., Ltd. | Our stainless steel float balls are designed for liquid level control applications in valves, tan... |
 |
"China manufacturer power supply VM-5H3 for power generation | Seller: DONGFANG YOYIK (DEYANG) ENGNIEERING CO; LTD | "China manufacturer power supply VM-5H3 for power generation Is to use the generator sets of prof... |
 |
Reliable Components for Water and Industrial Systems | Seller: Yongjia County Yaokang Technology Co., Ltd. | The Stainless Steel Float Ball is designed for automatic liquid level control and fluid managem... |
 |
Double Convex Lenses | Seller: Shandong Yanggu Constant Crystal Optics, Inc | Double Convex Lensesare used in image relay applications, or for imaging objects at close conjuga... |
