Heat Storage Performance Tester ASTM F2731
Standards
ASTM F2731 ?Standard Test Method for Measuring the Transmitted and Stored Energy of Firefighter Protective Clothing Systems
Applications
The equipment is used to detect heat storage and thermal transfer characteristics of protective clothing, safety shoes, gloves, helmet and other materials, and determine the possibility that protective equipment can cause skin burns when exposed to heat.
Product Information
Introduction
Heat Storage Performance Tester provides standardized procedures and controls radiation heat conditions, providing repetitive measurement for heat storage and thermal transfer of protective fabric materials. Through measurement, the characteristics and rating of the material can be quickly identified, and the possibility of burn to the material is predicted through the integrated burn model of the instrument.
Product Details
Instrument Structure:
The equipment includes radiant heat source, sample holder, calorimeter induction component, pneumatic start transfer tray with water-cooled slide frame, compressor, DAQ/control system and combustion injury analysis program.
Instrument Features:
·Assessing the possibility of skin burns which is related to the heat energy storage performance of fabric.
·Automatic or manual test operation
·Radiant plate heat source (adjustable temperature) generates radiation energy, which matches with the spectral line density of building fire.
·The water-cooled sample sliders, electronic driven, realizes the precise control of the time of exposure on the heat source.
·The pneumatic compressor uses a low conductivity core bar to apply a 1PSI load on the sample.
·The system includes the integrated burn model, which predicts the severity of skin injuries, and calculates the estimated time of exposure leading to secondary burns.
·The combustion results are real-time values and the graph shows the skin layer interface temperature and combustion synthesis of Omega.
System Including:
·Dell PC laptop.
·ThermDAC software with a combustion model
·Signal conditioning circuit and USB interface
·Power supply and control cable, operator manual
·One-year warranty.
Laboratory Requirement:
·The laboratory should be well ventilated with dry compressed air source and cooling water supply pipe.
·The desktop device is designed for operation of horizontal or vertical radiant heat sources.
·It is recommended to operate in a vertical direction.
Standard Specification
·The radiant heat plate range is 0-0.25 CAL/cm2. adjustable.
·There are two types of hot plate operating modes: temperature control or heat flow control.
·The water-cooled sample slider supports sample and copper calorimeter exposes the sensor.
·Pneumatic control compression system
·The sample compression force can be adjusted by changing the air pressure in the cylinder.
·Sample size: 6x6ft (15x15cm). Gaskets with different thickness can be provided to compress the edges of smaller samples.
Technical Parameters
| Items | Parameters |
| Dimension | 24.5”x 17”x 14”H（62x43x36cm H） |
| Space required | 36”x 20”x 16”H（92x51x41cm H） |
| Power | 200-265VAC，50/60Hz, single phase. Maximum rated current is 5Amps |
| Compressed air | Clean/dry air 50-90PSI |
| Cooling water | 32.5℃. The flow rate is 100ml/min or greater (Local tap water is acceptable ) |
| Radiant heat plate range | 0-0.25cal/cm2, adjustable |
| Sample size | 6x6 inches (15x15cm) |
Send product request
Other supplier products
 |
Standard Helmet Visual Field Tester | Standard Helmet Visual Field Tester - Other test instrument - standard Standards: EN1078:2023 Applications: 1. Used for marking test poin... |
 |
RPP Radiation Thermal Protection Performance Tester | Product Information: The RPP radiation protection performance tester is used to measure the amount of time that the radiation heat source penetrat... |
 |
Fully Automatic Continuous Flow Reaction Calorimeter | Product Features： 1. Using the coefficient calibration method and flow - regulation calorimetry, it can quickly obtain the reaction heat release a... |
 |
Respiratory Resistance Tester | Respiratory Resistance Tester Introduction: The respiratory resistance tester is used to determine the inspiratory and expiratory resistance of re... |
 |
Spinal Internal Fixation System Component Testing Machine | Standard YY/T 0119-2014 (China): Specifies mechanical testing protocols for spinal fixation components, including screws, plates, rods, and conn... |
Same products
 |
Plastic Smoke Density Tester F313 | Seller: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | Seller: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | Seller: Qinsun Instruments Co., LTD | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | Seller: Qinsun Instruments Co., LTD | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | Seller: Qinsun Instruments Co., LTD | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
