Micro Controll High-temperature Friction Tester
Applicable Standards
When conducting tests, the microcomputer - controlled high - temperature friction testing machine usually needs to comply with the following relevant national or international standards: - GB/T series standards: Relevant regulations on friction and wear testing in Chinese national standards, such as GB/T 12583 - 98 *Method for Determination of the Extreme - Pressure Properties of Lubricants (Four - ball Machine Method)*, etc.
Main Purposes
The microcomputer - controlled high - temperature friction testing machine is a device specifically designed for testing the frictional properties of materials in high - temperature environments. Its main purposes include, but are not limited to, the following aspects:
Material R & D and Evaluation
- Used to evaluate the friction and wear properties of various materials under high - temperature conditions, including metals, non - metals, coatings, rubbers, plastics, ceramics, etc.
- Helps in the research and development of new high - temperature - resistant materials and improves the high - temperature frictional properties of materials.
Lubricant and Oil Product Testing
- Test the frictional properties of lubricants, hydraulic oils, internal combustion engine oils, gear oils, etc. at high temperatures, and evaluate their lubrication effects and anti - wear capabilities. - Provide data support for the R & D, improvement, and quality control of lubricants and oil products.
Durability Testing of Mechanical Components
- Simulate the actual working conditions of mechanical components in high - temperature environments, test their friction and wear properties, and evaluate the durability and reliability of the components. - Contribute to optimizing mechanical designs and improving the service life and performance stability of mechanical components.
Technical parameters
Maximum test force 100KN
Tester accuracy 0.5 level
Test force measurement range 0.2%-100%FS All the way without gearing
Test force accuracy ±0.5% or less
Test force resolution 1/±300000 of the maximum test force (the whole resolution is unchanged)
Deformation measurement range 0.2%-100%FS
Relative error of the deformation value of the value of ±0.5% or less Within ±0.5%
Distinguishing power of deformation 1/±300000 of the maximum deformation
Dimensions of high and low temperature chamber 300mm*300mm*400mm
Temperature range Room temperature～600℃
Temperature fluctuation ±1℃
Relative error of displacement ±0.5% of the indicated value
Distinguishing power of displacement 0.05μm
Adjustment range of force rate 0.01-5%FS/S
Relative error of force rate ±0.5% of the setting value 0.5% of set value Within ±0.5% of set value
Transformation rate adjustment range 0.02-5%FS/S
Relative error of transformation control rate Within ±0.5% of set value
Transverse beam speed adjustment range 0.01-500mm/min
Relative error of transverse beam speed Within ±1.0% of set value for speed < 0.01mm/min; within ±1.0% of set value for speed ≥ 0.01mm/min. mm/min, within ±0.2% of the set value
Control range of constant force, constant deformation and constant displacement 0.5%-100%FS
Control accuracy of constant force, constant deformation and constant displacement When the set value is <10%FS, it is within ±1% of the set value; when the set value is ≥10%FS, it is within ±0.1% of the set value
Effective tensile space 700mm
Effective test width 600mm
Main machine appearance Dimensions (L×W×H) 800×600×2000 (mm)
Power supply 220V±10%,50Hz
Weight of mainframe about 500kg
Send product request
Other supplier products
 |
Thermal cycle wet freezing test device | Standard IEC 61215: Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval UL 1073: Standard for Safety for Enclosu... |
 |
Bone Plates Four-point Bending Fatigue Tester | Standard YY/T 1503-2016: Chinese standard specifying test methods for bending fatigue properties of metallic bone plates, requiring 1 million ... |
 |
Helmet UV pretreatment box | Product Introduction: Helmet ultraviolet pretreatment box is used for helmet ultraviolet irradiation pretreatment, according to the new national s... |
 |
UV Lamp Aging Test Tester | This product uses fluorescent UV lamps, combined with temperature and humidity device to simulate the material decline in color, brightness, streng... |
 |
Particle Strength Tester | Standard ASTM D4179: Standard Test Method for Single-Pellet Pressure Resistance of Catalysts and Catalyst Carriers ASTM D6175: Standard Test Me... |
Same products
 |
Custom Stainless Components for OEM Applications | Seller: Yongjia County Yaokang Technology Co., Ltd. | Our stainless steel float balls are designed for float valves, water tanks, and industrial liquid... |
 |
FH-77 Dissolved hydrogen meter | Seller: Kelilong Electron Co.,Ltd | Pen type dissolved hydrogen detector / dissolved hydrogen meter: used to measure the dissolved hy... |
 |
Xenon Arc Weather Ometer | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ... |
 |
Xenotest | Light Fastness Tester Si220 (SunTest) | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ... |
 |
Ozone Aging Chamber | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum... |
