Falling Sand Abrasion Test device
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Applicable Standard
JG/T 133-2000
ASTM D968-83
ASTMD333
ASTMD1395
ASTMD2205
Main Purposes
It is mainly used to test the abrasion - resistance of the lenses of helmet goggles and evaluate their ability to resist particle - induced damage.
Instructions For Use
1. according to the standard requirements for the preparation of test plates and placed in (23 +-2) degrees Celsius, relative humidity (50 +-5) degrees Celsius conditions for 24 hours.
2. Calibrate the apparatus:
Pour a certain amount of sand into the funnel, check the sand stream falling from the lower end of the conduit, and calibrate the device with the bottom adjusting screw until the inner part of the sand beam falls exactly on the center of the sand stream when viewed from two positions of 90 degrees Celsius each other. Use the high and low adjusting nut to adjust the distance from the tube tube to the painted surface according to the ASTM standard, when measured in the vertical direction, the near point of 1 inch (25mm), the user needs to be adjusted according to the thickness of their own samples, factory machine pre-adjustment of 25mm. to the pouring of a certain volume amount of sand (to 2000 +-10ml is appropriate), and measure the outflow time, the outflow rate should be 21S- 23.5S within 2L. This speed comes from the ASTM standard, and with the international standard sand for the test, we measured the speed of 1 minute 7L or more.
3. do the test should pay attention to, after the end of the sand fall, the machine should be slightly tilted to make the lower funnel in the small square of excess sand poured out, in the re-insertion of the sand fall switch in order to avoid the sand fall switch can not be put in.
Main Technical Parameters
Overall Dimension: 230mm×200mm×1500mm (L×W×H)
Catheter Length: 36 inches (914mm)
Catheter I.D.: 0.75 inches (19mm)
Hopper Volume: 3L
Machine Weight: 25KG
Send product request
Other supplier products
 |
Automated memory impact testing machine for research labs | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application Tapered twin-screw extruders are primarily used for direct forming of pipes, s... |
 |
CFR 1633 Mattress Flame Retardant Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Fire hazards exist everywhere in our daily life. In order to reduce fire accidents due to t... |
 |
Diaper Anti-Side Leakage Performance Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Diaper Anti-Side Leakage Performance Tester is designed to accurately measure the liqui... |
 |
Density of Smoke from the Burning or Decomposition of Plastics，ASTM D2843 Smoke Density Test | Whats/App: +86 156 1874 6768 Web: standard-groups.com Introduction In a fire, people are often smoke suffocated or unable to escape because of t... |
 |
Hydraulic Component Cleanliness Analysis System ISO 4407 | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Compliant standards VDA19.IS016232.NAS1638.IS04406 Particle standards Buil... |
Same products
 |
FH-77 Dissolved hydrogen meter | Seller: Kelilong Electron Co.,Ltd | Pen type dissolved hydrogen detector / dissolved hydrogen meter: used to measure the dissolved hy... |
 |
Xenon Arc Weather Ometer | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App: +86 181 0160 0864 SI4000Xenon Arc Weather Ometer utilizes a xenon lamp ... |
 |
Xenotest | Light Fastness Tester Si220 (SunTest) | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 180 0160 0864 A Light Fastness Tester, or Xenon Tester, Accelerated ... |
 |
Ozone Aging Chamber | Seller: Standard International Group (HK) Limited | Get a quote： Whats/App:+86 156 1874 6768 The Ozone Aging Chamber is a precision testing instrum... |
 |
Plastic Smoke Density Tester F313 | Seller: Standard International Group (HK) Limited | Whats/App: +86 156 1874 6768 Web: standard-groups.com The F313 Plastic Smoke Density Tester is ... |
