Single chip liquid crystal touch impact testing machine
Product Introduction:
Liquid crystal touch impact testing machine is mainly used for hard plastics （including sheet, pipe, plastic profile）， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.
Standards:
GB/T 18910.101-2021
IEC 60068-2-75:2014
Main features:
Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.
Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.
Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.
Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.
Performance parameters:
1. Simple beam impact testing machine
- Impact speed: 2.9m/s
- Impact energy: 1/2/4/5J
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 230mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz（single-phase three-wire system）
2. Cantilever beam impact testing machine
- Impact speed: 3.5m/s
- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J（3 hammers, customer's choice）
- Maximum friction loss energy: <0.5%
- Pendulum prelift Angle: 150±1°
- Strike center distance: 335mm
- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz（single-phase three-wire system）
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Wire Cut - through Tester for Ford Automotive Wires | Applicable Standard: Engineering Specification - Ford Global Wire specification, PART NO. ES - AU5T - 1A348 - AA Technical Parameters: 1. Sensin... |
 |
Smoke - Emission Testing Machine for Aerospace Wires and Cables-QINSUN | |
 |
Profilometer | Product Introduction: The profiler is measured by the slip of the stylus of the instrument and the surface to be measured, and is a contact measur... |
 |
Car seat center of gravity measuring tester | Main parameters: ParameterDescription Measuring range Refers to the maximum and minimum range of the center of gravity of the seat tha... |
 |
Automobile Wire Cross-linking Test Device | Applicable Standards: SAE J1128 - 2005 and other standards Main Parameters: 1. Test rod: Φ6mm, 300mm in length 2. Hot plate specification... |
Похожие товары
 |
Blanket Flammability Test Machine | Продавец: Standard Groups | Bed Blanket Flammability Tester-It is mainly used for testing the flame retardant performance of ... |
 |
High Temperature Oxygen Index Tester | Продавец: Standard Groups | The High-Temperature Oxygen Index (TOI) measuring instrument determines oxygen index at up to 125... |
 |
Limiting Oxygen Index Tester | Продавец: Standard Groups | The Limiting Oxygen Index Tester measures the minimum oxygen concentration needed to sustain comb... |
 |
Vertical Flammability Tester | Продавец: Standard Groups | Vertical Flammability Chamber for measuring the vertical flame spread for children’ sleepwe... |
 |
45 Degree Flammability Tester | Продавец: Standard Groups | Application 45 Degree Flammability Tester is used to determine the burning characteristics of te... |
