PLC liquid crystal touch impact testing machine (simple suspension)

• 

Product Introduction:

Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.

Standards:

GB/T 11022-2020. GB/T 3906-2020. JB/T 10840-2008.GB/T 7251.1-2013 ，GB/T 7251.4-2017.GB/T 7251.5-2017 ，GB/T 20641-2014

GB/T 20138-2006 ，GB/T2423.55-2006 ，Q/GDW11008-2013

Main features:

Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.

Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.

Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.

Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.

Performance parameters:

1. Simple beam impact testing machine

- Impact speed: 2.9m/s

- Impact energy: 1/2/4/5J

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 230mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

2. Cantilever beam impact testing machine

- Impact speed: 3.5m/s

- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 335mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

Другие товары поставщика

	50-125L automatic drum cleaning equipment, 11 to 28 gallon barrel washer	0-125L automatic drum cleaning equipment, 11 to 28 gallon barrel washer Design features： This complete barrel washer utilizes our rotary impingem...
	Fully Automatic Stripping Machine for Automotive Wires	The fully automatic stripping machine for automotive wires complies with the standards of GB/T2951 - 2008 and IEC60811 *General Test Methods for ...
	IBC Reconditioning System Tote washer Tunnel	For the cleaning of IBC tote, manual cleaning is still the main method. The internal cleaning of IBC container has always been a difficulty and pai...
	AATCC Blue wool cloth	Standards & Applications The AATCC Test Method TM 16 "Colorfastness to Light" utilizes a series of dyed blue wool fabrics as calibration and...
	Geomembrane thickness tester	Scope of application: Used to determine the thickness of smooth geomembrane and other plastic films under specified pressure and time. The sample ...

Похожие товары

	Высокоскоростная экструзионная линия для производства гофрированных труб с двойными стенками из ПЭВП с водяным охлаждением	Продавец: Shandong HUASU Plastic Technology Co.,Ltd.	Формы имеют структуру с двойным каналом потока и фильерную головку, обработанную азотированием и ...
	PanEVAP & MVR system	Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat...
	PanGAP wide gap welded plate heat exchanger	Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel...
	PanBloc welded plate heat exchanger	Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac...
	PanBox welded plate heat exchanger	Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated...