PLC liquid crystal touch impact testing machine (simple suspension)

• 

Whats/App: +86 156 1874 6768

Web: standard-groups.com

A PLC LCD Touch Impact Testing Machine (Simple Suspension) is a type of pendulum impact tester designed to measure the impact resistance of materials using a simple (pendulum) suspension system, with modern control via a PLC (Programmable Logic Controller) and an LCD touchscreen interface.

Product Introduction

Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.

Standards

(1)GB/T 11022-2020. GB/T 3906-2020. JB/T 10840-2008.GB/T 7251.1-2013 ，GB/T 7251.4-2017.GB/T 7251.5-2017 ，GB/T 20641-2014

(2)GB/T 20138-2006 ，GB/T2423.55-2006 ，Q/GDW11008-2013

Main features

Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.

Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.

Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.

Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.

Performance parameters

1. Simple beam impact testing machine

- Impact speed: 2.9m/s

- Impact energy: 1/2/4/5J

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 230mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

2. Cantilever beam impact testing machine

- Impact speed: 3.5m/s

- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 335mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

Другие товары поставщика

	Simulation Dummy for HVAC, Automotive, and Safety Testing	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Simulation Test Dummy is a high-fidelity anthropomorphic test device (ATD) specifically...
	Intramedullary Nails Four - point Bending Fatigue Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard YY/T 0591-2011: Chinese standard specifying bending fatigue test methods for intr...
	Safety Helmet High Temperature Pre-Treatment Chamber	Whats/App: +86 156 1874 6768 Web: standard-groups.com The safety helmet high-temperature pre-treatment chamber is manufactured according to the G...
	Touchscreen tapping and scratching life test equipment	Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards (1) GB/T 4208-2017 – Degrees of protection provided by enclosures (IP Code...
	Rotary Reciprocating Friction Wear Testing Machine	Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications You can use this tester to: Evaluate the tribological performance of materia...

Похожие товары

	ER4043 Silicon Aluminum Welding Wire	Продавец: 868776	Hangzhou Kunli Welding Materials Co., Ltd. specializes in manufacturing high-quality welding mate...
	Choosing the Right Equipment for Heavy-Duty Cleaning	Продавец: Taizhou Feike Mechanical Technology Co., Ltd.	FEIKE’s High Pressure Washer is designed for industrial cleaning, equipment maintenance, ve...
	ER4043 Silicon Aluminum Welding Wire	Продавец: 868776	Hangzhou Kunli Welding Materials Co., Ltd. offers ER4043 Silicon Aluminum Welding Wire for alumin...
	Высокоскоростная экструзионная линия для производства гофрированных труб с двойными стенками из ПЭВП с водяным охлаждением	Продавец: Shandong HUASU Plastic Technology Co.,Ltd.	Формы имеют структуру с двойным каналом потока и фильерную головку, обработанную азотированием и ...
	PanEVAP & MVR system	Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd	A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat...