MMT Liquid Water Separation Tester
Getaquote：
Whats/App: +86 181 0160 0864
TheMMT Liquid Water Separation Testeris a precision instrument designed to evaluate the water repellency and separation efficiency of textile materials, coatings, and membranes. It quantifies liquid absorption resistance and hydrophobic performance using standardized spray and drainage methods, critical for waterproof fabric development and quality assurance.
Applications
Textile Manufacturing:Testing waterproof fabrics for outdoor gear
R&D:Developing hydrophobic coatings for medical textiles
Quality Control:Batch inspection of rainwear
Forensic Analysis:Evaluating fabric degradation from water exposure
Standards
AATCC 22 (Spray Rating), ISO 4920 (Water resistance)
Key Metrics:
Water Repellency Rating (0–5 scale)
Separation Efficiency (%)
Absorption Time (seconds)
Sample Size: 150×150mm (adjustable clamping)
Compliance Standards
AATCC 22 (Water repellency spray test)
ISO 4920 (Textile water resistance)
EN 343 (European waterproof standard)
GB/T 4744 (Chinese hydrostatic pressure test)
Features
Dual Test Modes:
Spray Test:AATCC 22 vertical hydrophobicity evaluation
Drainage Test:ISO 4920 dynamic water separation
Advanced Detection:
High-speed camera (120fps) with image analysis
AI-based droplet tracking (5 severity levels)
Real-time absorption rate calculation
Automation:
Auto-fill/empty water reservoir
Programmable nozzle angle adjustment
Self-cleaning drainage system
Technical Parameters
| Parameter | Specifications |
|---|---|
| Spray System | 12-nozzle array (0.5mm droplet size) |
| Water Pressure | 50±5 kPa (programmable) |
| Test Duration | 1–30 minutes (auto-stop) |
| Drainage Rate | 1.5L/min (recirculating system) |
| Measurement Accuracy | ±1% FS (ISO 376 standard) |
| Dimensions | 800×600×1200mm (L×W×H) |
Accessoriess
1. Main unit;
2. Analysis software;
3. Conductivity tester
Test Procedures
1. Sample Preparation
Select the knitted/woven fabric sample to be tested, ensuring the sample is flat and undamaged.
2. Sample Installation
Install the sample into the testing area between the upper and lower concentric liquid sensors of the testing instrument, ensuring the sample is in close contact with the test area.
3. Instrument Adjustment
Check the condition of the instrument's infusion tubing, probes, and other components, and adjust the instrument to a ready state.
4. Simulated Droplet Application
Through the infusion tubing of the upper sensor, evenly drip simulated human sweat onto the fabric surface according to the set fixed concentration and amount.
5. Test Startup
Start the instrument and use the sensor probes to monitor the resistance changes at different stages (to reflect the absorption/diffusion of the liquid in the fabric).
6. Parameter Acquisition
After the test, read the parameters output by the instrument (upper/lower layer wetting time, sweat absorption rate, maximum diffusion radius, etc.) to complete the evaluation of the fabric's liquid moisture management capability.
Отправить запрос, связаться с поставщиком
Другие товары поставщика
 |
Midsole Fibreboard Bending Test Machine - STD G664 | Product Introduction: G664 mid-sole fiberboard zigzag testing machine Test leather shoes and casual shoes, walking shoes and other travel shoes, m... |
 |
Filter Membrane Pore Analysis Tester | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The Filter Membrane Pore Analysis Tester is a precision instrument designed to mea... |
 |
Heat Extension Tester | Get a quote： Whats/App: +86 181 0160 0864 The Heat Extension Tester is designed to measure the elongation and deformation of electrical wire and ... |
 |
Fully Automatic AC/DC High - Voltage Tester for Wires and Cables | Get a quote： Whats/App: +86 181 0160 0864 The fully automatic AC/DC high-voltage tester is specially designed to test the insulation performance ... |
 |
NES 713 Navy Engineering Smoke Toxicity Test Chamber | Get a quote： Whats/App: +86 181 0160 0864 Web: gellowen.co.uk The NES 713 Navy Engineering Smoke Toxicity Test Chamber is a specialized fire tes... |
Похожие товары
 |
Высокоскоростная экструзионная линия для производства гофрированных труб с двойными стенками из ПЭВП с водяным охлаждением | Продавец: Shandong HUASU Plastic Technology Co.,Ltd. | Формы имеют структуру с двойным каналом потока и фильерную головку, обработанную азотированием и ... |
 |
PanEVAP & MVR system | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
 |
PanBox welded plate heat exchanger | Продавец: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBox welded plate heat exchangerconsists of a laser welded plate pack with optimized corrugated... |
