Rupture strength tester

Whats/App: +86 156 1874 6768

Web: standard-groups.com

The Rupture Strength Tester is designed to evaluate the mechanical pressure resistance and rupture strength of photovoltaic module components under controlled pressurization conditions. The system applies uniform hydraulic or pneumatic pressure to determine the failure threshold of module glass, backsheets, and encapsulation structures, supporting safety qualification and structural reliability assessment of photovoltaic modules.

Application

(1) Rupture strength testing of photovoltaic module front glass

(2) Pressure resistance evaluation of PV module backsheets and encapsulants

(3) Safety verification of single-glass and dual-glass photovoltaic modules

(4) Mechanical integrity assessment under simulated wind and snow loads

(5) Quality control and type approval testing in PV module manufacturing

(6) Failure analysis and material comparison in PV R&D laboratories

Standards

(1) IEC 61730-2 – Photovoltaic (PV) Module Safety Qualification – Requirements for Testing

(2) UL 61730 – Safety Standard for Photovoltaic Modules

(3) CE Certification (Conformité Européenne)

Features

(1) Wide Pressure Capability: Suitable for rupture testing of thin-film, crystalline silicon, and dual-glass PV modules.

(2) High-Resolution Pressure Control: Enables early detection of micro-cracking and progressive structural failure.

(3) Multi-Unit Measurement Interface: Supports kPa, psi, and kg/cm² for international testing requirements.

(4) Enhanced Safety Structure: Reinforced test chamber allows safe observation of specimen rupture.

(5) Automated Test Control: Preset pressure ramp and holding sequences reduce operator variability.

(6) Integrated Data Recording: Pressure–time curves and rupture values stored for traceability and analysis.

(7) Robust Construction: Stainless steel frame ensures long-term stability under repeated high-pressure operation.

Parameters

Parameter	Specification
Pressure Range	250–5,600 kPa (36–812 psi)
Pressure Resolution	0.01 kg/cm²
Holding Pressure	5 kg/cm² (adjustable)
Control Accuracy	±1% FS (full scale)
Air Source Requirement	≥6 kg/cm² (customer-provided)
Power Supply	220V AC, 50/60Hz, single-phase
Dimensions	560 mm (W) × 470 mm (D) × 550 mm (H)
Weight	60 kg (net)

Accessories

(1) Testing Fixtures: 1× specialized clamping fixture for 2–20 mm module thickness

(2) Membranes: 2× high-temperature rubber membranes (up to 300°C)

(3) Calibration Tools: 5× aluminum foil calibration discs

(4) Consumables: 85% glycerin solution for hydraulic calibration, disposable dust filters

(5) Safety Equipment: Safety goggles (ANSI Z87.1), emergency pressure release key

(6) Documentation: Multilingual quick-start guide and IEC/UL compliance certificates

Test Procedures

(1) Install the PV module specimen securely into the clamping fixture.

(2) Select pressure unit, ramp rate, and holding parameters via the touchscreen interface.

(3) Initiate pressurization and monitor real-time pressure increase.

(4) Maintain holding pressure as specified or continue ramping until rupture occurs.

(5) Record rupture pressure, pressure–time curve, and failure mode automatically.

Maintenance Information

(1) Inspect sealing membranes and clamping fixtures regularly for wear or deformation.

(2) Verify pressure sensor calibration at scheduled intervals.

(3) Clean the test chamber after each rupture test to remove debris.

(4) Check safety valves and electronic cut-off functions before routine operation.

(5) Store the tester in a clean, dry environment to maintain long-term accuracy.

Другие товары поставщика

	Male Side Impact Dummy (RE Type)	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Male Side Impact Dummy (RE Type) is a high-fidelity side impact test dummy designed bas...
	Zipper Reciprocating Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com Zipper reciprocating tester measures zipper performance in products like clothes and bags. ...
	SUGA GX75 7.5kW Xenon Weather Meter	Whats/App: +86 156 1874 6768 Web: standard-groups.com Applicable Standards The GX75 meets stringent international standards, including: ISO 4...
	Photovoltaic module outdoor exposure test system	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Photovoltaic Module Outdoor Exposure Test System is designed to simulate real-world env...
	Color Stability Tester for Dental Materials	Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Dentistry Base Polymer Search Stability tester evaluates color stability ...

Все товары поставщика

Похожие товары

	Large Naïve VHH Library	Продавец: AlpVHHs	Large Naïve VHH Library VHHare single-domain antibodies derived from the variable regions o...
	pH-2398 pH/EC/ORP/Temperature multi-parameter Water Quality Tester	Продавец: Коллирон электроникс лимитед	Feature Large display screen, capable of simultaneously measuring water quality pH, redox potent...
	ORP-2026S Waterproof Soil ORP and Temperature Meter	Продавец: Коллирон электроникс лимитед	范围 ORP -999～999mV Temp 0～50℃ 分辨率 ORP 1mV...
	TDS-2616 Waterproof EC/TDS/Temperature Meter	Продавец: Коллирон электроникс лимитед	Range EC ～19.9mS TDS Temp 0～50℃ R...
	EC-98330 CF ECOstick - Nutrient Tester	Продавец: Коллирон электроникс лимитед	Ideal for hydroponics and agriculture applications, theNutrient Tester accurately measures the el...