Drawer slide durability testing machine

The Drawer Slide Durability Testing Machine is designed to evaluate the mechanical durability, operational reliability, and service life of drawer slide systems under repeated opening and closing cycles. The equipment simulates long-term daily use by applying controlled reciprocating push–pull motion to drawer slides, enabling accelerated life testing under standardized and repeatable conditions. It is used to identify wear, deformation, functional degradation, and potential failure modes of drawer slide assemblies in accordance with furniture hardware durability standards.

Application

(1) Durability and life cycle testing of furniture drawer slides (ball bearing slides, roller slides, concealed slides) used in residential and commercial furniture

(2) Performance evaluation of cabinet drawer slides (kitchen cabinets, bathroom cabinets, office storage units) under repeated opening and closing cycles

(3) Quality control testing for drawer slide manufacturers (steel slides, aluminum slides, soft-close slides) during production inspection

(4) Type testing and compliance verification of drawer slide systems for furniture hardware certification and standard conformity

(5) Research and development testing of new drawer slide designs, materials, and surface treatments to improve wear resistance and service life

Standards

(1) ANSI/BIFMA X5.5 – Desk Products: Tests for Drawer Durability and Performance

(2) BIFMA X5.5-2008 – Desk Products Durability and Functional Performance Requirements

(3) EN 15338 – Furniture Hardware – Strength and Durability Requirements for Drawer Slides

(4) ISO 7170 – Furniture – Storage Units – Determination of Strength and Durability

(5) QB/T 2454-2013 – Furniture Hardware – Drawer Slide Rails

Features

(1) PLC control system combined with stepper motor drive ensures high repeatability and precise control of test motion

(2) Adjustable reciprocating push–pull speed allows simulation of different usage frequencies and operating conditions

(3) Programmable test counter with automatic shutdown enables unattended long-duration testing

(4) Wide adjustable mounting width with linear bearing structure supports a broad range of drawer slide sizes and types

(5) Multi-station design improves testing efficiency and allows parallel evaluation of multiple samples

Parameters

Item	Description
Reciprocating speed	1–15 times/min, adjustable
Test cycle counter	1–999,999 cycles, preset with automatic stop
Push–pull stroke	100–600 mm, adjustable
Control mode	PLC control, adjustable slide stop time
Installation width	100–900 mm, adjustable
Slide mounting structure	Ø30 mm guide rod with linear bearing
Test stations	1–6 stations
Drive motor	Stepper motor, PLC program controlled
Power supply	AC 220 V, 60 Hz

Accessories

(1) Standard drawer slide mounting fixtures for different slide sizes

(2) PLC touch control panel for parameter setting and monitoring

(3) Electrical control cabinet integrated with motor drive system

Test Procedures

(1) Install the drawer slide sample securely on the mounting fixture and adjust installation width and alignment

(2) Set test parameters including stroke length, reciprocating speed, stop time, and total test cycles on the PLC interface

(3) Start the test and allow the machine to perform automatic reciprocating push–pull motion

(4) Monitor test operation periodically to check sample condition and machine status

(5) After reaching the preset cycle count or sample failure, stop the test and record test results

Maintenance Information

(1) Clean guide rails, fixtures, and working surfaces regularly to prevent dust and debris accumulation

(2) Inspect mechanical transmission components and fasteners periodically for looseness or wear

(3) Lubricate linear bearings and moving parts according to recommended maintenance intervals

(4) Disconnect power supply and store the equipment in a dry environment when not in use for extended periods

Другие товары поставщика

	STD Battery short-circuit tester	The Battery Short-Circuit Tester is designed for external short-circuit safety testing of lithium-ion batteries and battery packs. The system simu...
	Tracking indices of solid insulating materials Test Machine ,IEC60112	Introduction This tester is in accordance with IEC60112 standard . It is suitable for lighting, low voltage electrical equipment, household appl...
	Metal Bone Screws Self - tapping Tester	Standard ISO 6475: Implants for surgery – Wear of total hip-joint prostheses ASTM F543: Standard Specification and Test Methods for Metalli...
	Full Face Masks Flame Resistance Test Machine	Introduction Fireman fire-protective clothing is mainly composed of jacket and bibcomposition,may also wear fire protective helmets, fire protec...
	Catheter Friction Tester	The Catheter Friction Tester is a precision instrument used to measure the surface friction properties of various tubular materials. Employing adva...

Все товары поставщика

Похожие товары

	Full-Body Garment Stress Tester,FZ/T 70015	Продавец: Standard International Group (HK) Limited	TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe...
	Industrial Dry Cleaning Machine,industrial garment steamer	Продавец: Standard International Group (HK) Limited	TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel...
	MST Medical Compression Stocking Tester,compression sock tester	Продавец: Standard International Group (HK) Limited	The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the...
	MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool	Продавец: Standard International Group (HK) Limited	Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi...
	Dental material color stability tester	Продавец: Standard International Group (HK) Limited	Application The applications of color stability testers for dental materials are mainly reflecte...