Drawer slide durability testing machine

The Drawer Slide Durability Testing Machine is designed to evaluate the mechanical durability, operational reliability, and service life of drawer slide systems under repeated opening and closing cycles. The equipment simulates long-term daily use by applying controlled reciprocating push–pull motion to drawer slides, enabling accelerated life testing under standardized and repeatable conditions. It is used to identify wear, deformation, functional degradation, and potential failure modes of drawer slide assemblies in accordance with furniture hardware durability standards.

Application

(1) Durability and life cycle testing of furniture drawer slides (ball bearing slides, roller slides, concealed slides) used in residential and commercial furniture

(2) Performance evaluation of cabinet drawer slides (kitchen cabinets, bathroom cabinets, office storage units) under repeated opening and closing cycles

(3) Quality control testing for drawer slide manufacturers (steel slides, aluminum slides, soft-close slides) during production inspection

(4) Type testing and compliance verification of drawer slide systems for furniture hardware certification and standard conformity

(5) Research and development testing of new drawer slide designs, materials, and surface treatments to improve wear resistance and service life

Standards

(1) ANSI/BIFMA X5.5 – Desk Products: Tests for Drawer Durability and Performance

(2) BIFMA X5.5-2008 – Desk Products Durability and Functional Performance Requirements

(3) EN 15338 – Furniture Hardware – Strength and Durability Requirements for Drawer Slides

(4) ISO 7170 – Furniture – Storage Units – Determination of Strength and Durability

(5) QB/T 2454-2013 – Furniture Hardware – Drawer Slide Rails

Features

(1) PLC control system combined with stepper motor drive ensures high repeatability and precise control of test motion

(2) Adjustable reciprocating push–pull speed allows simulation of different usage frequencies and operating conditions

(3) Programmable test counter with automatic shutdown enables unattended long-duration testing

(4) Wide adjustable mounting width with linear bearing structure supports a broad range of drawer slide sizes and types

(5) Multi-station design improves testing efficiency and allows parallel evaluation of multiple samples

Parameters

Item	Description
Reciprocating speed	1–15 times/min, adjustable
Test cycle counter	1–999,999 cycles, preset with automatic stop
Push–pull stroke	100–600 mm, adjustable
Control mode	PLC control, adjustable slide stop time
Installation width	100–900 mm, adjustable
Slide mounting structure	Ø30 mm guide rod with linear bearing
Test stations	1–6 stations
Drive motor	Stepper motor, PLC program controlled
Power supply	AC 220 V, 60 Hz

Accessories

(1) Standard drawer slide mounting fixtures for different slide sizes

(2) PLC touch control panel for parameter setting and monitoring

(3) Electrical control cabinet integrated with motor drive system

Test Procedures

(1) Install the drawer slide sample securely on the mounting fixture and adjust installation width and alignment

(2) Set test parameters including stroke length, reciprocating speed, stop time, and total test cycles on the PLC interface

(3) Start the test and allow the machine to perform automatic reciprocating push–pull motion

(4) Monitor test operation periodically to check sample condition and machine status

(5) After reaching the preset cycle count or sample failure, stop the test and record test results

Maintenance Information

(1) Clean guide rails, fixtures, and working surfaces regularly to prevent dust and debris accumulation

(2) Inspect mechanical transmission components and fasteners periodically for looseness or wear

(3) Lubricate linear bearings and moving parts according to recommended maintenance intervals

(4) Disconnect power supply and store the equipment in a dry environment when not in use for extende

Другие товары поставщика

	Safety Helmet Chin-strap Strength Tester	Standard GB/T 2812-2006: Safety Helmets GB/T 2811-2019: Head Protection – Vocabulary and Test Methods Equivalent Compliance: ISO/EN 397 (I...
	Photovoltaic module outdoor exposure test system	The Photovoltaic Module Outdoor Exposure Test System is designed to simulate real-world environmental conditions for accelerated aging and performa...
	Fiber Composition Ratio Analyzer (for Fiber Blend Ratio Tester)	Product Introduction: It is used to measure the resistance value with a certain density under a certain geometry, and then converts it into the sp...
	1.5 M Long UV Curing Machine For Screen Printing Paper Sheet CE Approved	Product information UV is the ultraviolet (Ultra-VioletRay) English abbreviation. Industrial UV wavelength to 200nm to 450nm for its scope of ap...
	Protective Clothing Resistance Tester	Related Standards GB/T 22042 - 2008 Clothing - Anti-static Performance - Test Method for Surface Resistivity GB/T 22043 - 2008 Clothing - Anti-st...

Все товары поставщика

Похожие товары

	Gas Oxidizing Property Tester	Продавец: Standard International Group (HK) Limited	Product Description Conforms to ISO 10156-2010 “Gases and Gas Mixtures Selection of Cylind...
	Battery Powder Compaction Density Measurement System	Продавец: Standard International Group (HK) Limited	The Battery Powder Compaction Density Measurement System is a precision testing system designed...
	Battery Powder resistance tester	Продавец: Standard International Group (HK) Limited	The Powder Resistivity Meter is a precision testing system designed to measure electrical resisti...
	KES-SESRU surface roughness/friction tester	Продавец: Standard International Group (HK) Limited	TheRoughness/Friction Tester analyzes hand movements-particularly, strokes-performed by artisans ...
	Air Permeability Tester STD- F8	Продавец: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...