Yellowing resistance test chamber

• 

The yellowing resistance test chamber, a key testing device in the field of materials science, accurately evaluates the color stability of materials during long-term use by simulating sunlight ultraviolet radiation and high-temperature environments. This equipment is widely used in industries such as plastics, rubber, textiles, coatings, and electronic products, providing a scientific basis for product quality control and material development.

Applications

Test method for determining the yellowing resistance of light and white products, such as upper and bottom materials for shoes, to approximate sunlight and ultraviolet light. According to the light-colored or white products, the phenomenon of yellow color is easy to occur in the natural sunlight for a long time, with the solar lamp and heating temperature control device to simulate the natural environment, within the specified time, observe the change of the surface color of the sample, determine the degree of discoloration of the sample, so as to determine the ability of the material to resist yellow under sunlight radiation.

Standards

HG/T3986:Plastic tower filler

ASTM D1748-24:Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet

Features

This machine is designed to promote the metamorphism of vulcanized materials and then calculate the rate of change, stretching, and elongation. It also simulates the effects of ultraviolet radiation and heat from the sun. Samples are placed on the machine's table and subjected to UV radiation and temperature. Over time, the degree of yellowing and discoloration of the samples is observed, and the grayscale values can be used as a reference to determine the extent of yellowing. This is relevant to products that are exposed to radiation or sunlight during transportation.

The machine addresses the impact of color changes in the container environment on product quality. Using a 300W UV lamp, the experiment can be completed in a shorter time. This machine can be used as a basic yellowing resistance testing machine, an aging testing machine, and an oven, demonstrating its multi-functional capabilities. The machine is equipped with a forced hot air circulation control system to ensure uniform temperature distribution.

Technical Parameters

Accessoriess

Stainless steel test panel, high-temperature resistant observation window, single-layer test rack assembly, operating manual + certificate of conformity, power cord, fuse.

Test Procedures

1. Powering On and Preheating

Connect the test chamber to the power supply, turn on the main power switch, and wait for the system self-check to complete. After the self-check is successful, set the ultraviolet intensity, temperature, humidity, and other parameters according to the preset values, and start the equipment preheating program. The preheating time is generally 15-30 minutes. Samples can only be placed in the chamber after the temperature and humidity inside the chamber have reached a stable state.

2. Sample Placement and Test Start

Open the test chamber door, carefully place the prepared samples on the sample rack, ensuring that the samples do not obstruct the ultraviolet lamps and will not shake or move during equipment operation. Close the chamber door, confirm that the seal is good, and then click the "Start" button. The equipment will then officially enter the testing phase.

3. Process Monitoring and Recording

During the test, you can view real-time changes in temperature, humidity, ultraviolet intensity, and other data through the equipment control panel or accompanying software. It is recommended to record data every 1-2 hours. If abnormal parameter fluctuations are detected (such as a temperature deviation exceeding ±2℃ or a humidity deviation exceeding ±5%), the test must be immediately paused, the cause investigated and corrected before continuing. Regularly observe changes in the sample's appearance, such as yellowing or surface cracking, take photos for documentation, and record the details.

4. Test Completion and Sample Handling

When the preset test duration is reached, the equipment will automatically stop running. After the temperature inside the chamber drops to room temperature, open the chamber door and remove the samples. Place the samples in a standard laboratory environment (temperature 23±2℃, humidity 50±5%) for 2-4 hours to recover, then use a colorimeter, visual comparison, etc., to evaluate the yellowing resistance level and complete the test report.

Другие товары поставщика

	Bag Plastic Buckle Durability Tester	It is mainly used to test the service life of plastic plug-ins in luggage accessories. Applications This machine simulates the use of plastic cla...
	Protective Clothing Resistance Test device	Related Standards GB/T 22042 - 2008 Clothing - Anti-static Performance - Test Method for Surface Resistivity GB/T 22043 - 2008 Clothing - Anti-st...
	Aluminum Ointment Tube Toughness Tester	The ductility tester for aluminum tubes is a device specifically used to detect the ductility indicators of packaging materials such as aluminum so...
	Four-point Bending Tester	Standard YY/T 0591 (China): Standard for static four-point bending tests of lockable intramedullary nails. ASTM F1264 (International): Specificat...
	Bone Cement Four-Point Bending Fatigue Tester	Standard YY/T 1429 (China): Specifies four-point bending fatigue tests for acrylic resin bone cements under quasi-static and cyclic loading. ISO ...

Похожие товары

	Gas Oxidizing Property Tester	Продавец: Standard International Group (HK) Limited	Product Description Conforms to ISO 10156-2010 “Gases and Gas Mixtures Selection of Cylind...
	Battery Powder Compaction Density Measurement System	Продавец: Standard International Group (HK) Limited	The Battery Powder Compaction Density Measurement System is a precision testing system designed...
	Battery Powder resistance tester	Продавец: Standard International Group (HK) Limited	The Powder Resistivity Meter is a precision testing system designed to measure electrical resisti...
	KES-SESRU surface roughness/friction tester	Продавец: Standard International Group (HK) Limited	TheRoughness/Friction Tester analyzes hand movements-particularly, strokes-performed by artisans ...
	Air Permeability Tester STD- F8	Продавец: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...