Walk-in High-Temperature Aging Chamber,walk in stability chamber

Applications

Walk-in High-Temperature Aging Chambers are typically assembled on-site using insulated panels (double-sided color steel sheets with insulation material in between). Chamber dimensions are customized to client specifications. The complete walk-in high/low temperature and humidity test chamber features comprehensive safety protection devices and provides troubleshooting methods, with safety ratings surpassing other brands. Protection Devices: Fuse-less switches, fuses, over-temperature protection, dry-run protection, low-water protection, liquid level protection, compressor overpressure, overheat, and overcurrent protection. Comprehensive protection includes compressor overload/overheat protection, phase loss protection, and a fault alarm system.

Standards

GJB150.3 (ML-STD-810D) High Temperature Test Method

GJB150.4 (MIL-STD-810D) Low Temperature Test Method

GJB360.8-87 (MIL-STD-202f) High Temperature Life Test

GB/T5170.2-96 Temperature Test Equipment

GB2423.1-89 (IEC68-2-1) Basic Environmental Test Procedures for Electrical and Electronic Products Test A: Low Temperature Test Method

GB2423.2-89 (IEC68-2-2) Basic Environmental Test Procedures for Electrical and Electronic Products - Test B: High Temperature Test Method

GB5170. 2. 3. 5. 6-95 “Calibration Methods for Basic Parameters of Environmental Test Equipment for Electrical and Electronic Products - Low Temperature, High Temperature, Constant Humidity and Heat, Alternating Humidity and Heat Test Equipment” Requirements

Features

1. Simple maintenance and user-friendly operation are key advantages of our products.

2. The independent frame design ensures the refrigeration system and air distribution system operate separately.

3. Maintenance and repairs can be performed during unit operation, resulting in low annual failure rates and simplified, rapid servicing.

Parameters

Item	Specifications
Dimensions	200 cm (W) × 200 cm (H) × 200 cm (D); customizable per customer requirements, with external dimensions subject to actual size
Temperature Range	Optional ranges: 0°C~20°C / -40°C~60°C / -70°C~+85°C / 100°C (lower temperature ranges are higher in cost; choose based on product needs)
Temperature Fluctuation	±0.5°C (defined as half the difference between the highest and lowest measured temperatures at the center point)
Temperature Uniformity	±2.0°C (defined as the arithmetic mean of the differences between highest and lowest measured temperatures per test)
Heating Time	From room temperature (+10°C) to +85°C: <60 minutes, non-linear no-load heating rate ≈3°C/min
Cooling Time	- From +10°C to 0°C: <30 minutes, non-linear no-load cooling rate ≈1°C/min- From +10°C to -20°C: <45 minutes, non-linear no-load cooling rate ≈1°C/min- From +10°C to -40°C: <60 minutes, non-linear no-load cooling rate ≈1°C/min
Operating Noise	A-weighted sound level ≤60 dB(A), measured in anechoic chamber at 25°C ambient temperature, using A-weighting, averaged over 8 test points (each at 1m from noise source and 1m above ground)

Accessories

Temperature and humidity sensors

LED display control panel with PID auto-tuning

Stainless steel air circulation ducts and heating elements

Safety devices: fuses, overload protection, leakage detection

Adjustable shelving for test samples

Test Procedures

1. Pre-Operation Preparation

Train personnel on safety procedures, emergency stop methods, and chamber operation.

Verify grounding and electrical system integrity; ensure voltage is within specifications (~380V).

Ensure adequate ventilation and unobstructed exhaust system.

Wear appropriate personal protective equipment (PPE) including heat-resistant gloves, safety shoes, and protective eyewear.

2. Sample Placement

Arrange test samples to avoid overcrowding and ensure uniform airflow.

Ensure sample weight and volume do not exceed chamber limits.

3. Operation

Set desired temperature and duration according to test protocol.

Start the chamber and monitor temperature via PID control system.

Check for abnormal readings or fluctuations; adjust settings as necessary.

4. Monitoring During Test

Continuously monitor internal temperature and airflow.

Inspect for leaks or abnormal fumes if using gas or electric heating.

Restrict access to authorized personnel only.

Другие товары поставщика

	Pinhole Tester	The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in aluminum foil materials. Applications The pinhol...
	Weatherometer Laboratory Testing Equipment(UV)	Features and Benefits 1. UVA-340. UVB-313 and other UV lamps, a single power of 40 watts, can accurately control the irradiation intensity of 0....
	Rubber hose outer coating wear testing machine	The Rubber Hose Outer Coating Wear Testing Machine is a precision laboratory and production testing instrument designed to evaluate the abrasion re...
	Hot Tack Tester / Heat Seal Tester	The Hot Tack Tester/Heat Seal Tester is specifically designed for testing the heat-adhesion and heat-sealing properties of packaging materials such...
	Fire retardant wood wood stack method burning test equipment	Product Introduction: Fire retardant wood stack method combustion test device is a test device developed and produced by referring to the People's...

Все товары поставщика

Похожие товары

	Full-Body Garment Stress Tester,FZ/T 70015	Продавец: Standard International Group (HK) Limited	TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe...
	Industrial Dry Cleaning Machine,industrial garment steamer	Продавец: Standard International Group (HK) Limited	TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel...
	MST Medical Compression Stocking Tester,compression sock tester	Продавец: Standard International Group (HK) Limited	The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the...
	MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool	Продавец: Standard International Group (HK) Limited	Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi...
	Dental material color stability tester	Продавец: Standard International Group (HK) Limited	Application The applications of color stability testers for dental materials are mainly reflecte...