Rupture strength tester

Whats/App: +86 156 1874 6768

Web: standard-groups.com

The Rupture Strength Tester is designed to evaluate the mechanical pressure resistance and rupture strength of photovoltaic module components under controlled pressurization conditions. The system applies uniform hydraulic or pneumatic pressure to determine the failure threshold of module glass, backsheets, and encapsulation structures, supporting safety qualification and structural reliability assessment of photovoltaic modules.

Application

(1) Rupture strength testing of photovoltaic module front glass

(2) Pressure resistance evaluation of PV module backsheets and encapsulants

(3) Safety verification of single-glass and dual-glass photovoltaic modules

(4) Mechanical integrity assessment under simulated wind and snow loads

(5) Quality control and type approval testing in PV module manufacturing

(6) Failure analysis and material comparison in PV R&D laboratories

Standards

(1) IEC 61730-2 – Photovoltaic (PV) Module Safety Qualification – Requirements for Testing

(2) UL 61730 – Safety Standard for Photovoltaic Modules

(3) CE Certification (Conformité Européenne)

Features

(1) Wide Pressure Capability: Suitable for rupture testing of thin-film, crystalline silicon, and dual-glass PV modules.

(2) High-Resolution Pressure Control: Enables early detection of micro-cracking and progressive structural failure.

(3) Multi-Unit Measurement Interface: Supports kPa, psi, and kg/cm² for international testing requirements.

(4) Enhanced Safety Structure: Reinforced test chamber allows safe observation of specimen rupture.

(5) Automated Test Control: Preset pressure ramp and holding sequences reduce operator variability.

(6) Integrated Data Recording: Pressure–time curves and rupture values stored for traceability and analysis.

(7) Robust Construction: Stainless steel frame ensures long-term stability under repeated high-pressure operation.

Parameters

Parameter	Specification
Pressure Range	250–5,600 kPa (36–812 psi)
Pressure Resolution	0.01 kg/cm²
Holding Pressure	5 kg/cm² (adjustable)
Control Accuracy	±1% FS (full scale)
Air Source Requirement	≥6 kg/cm² (customer-provided)
Power Supply	220V AC, 50/60Hz, single-phase
Dimensions	560 mm (W) × 470 mm (D) × 550 mm (H)
Weight	60 kg (net)

Accessories

(1) Testing Fixtures: 1× specialized clamping fixture for 2–20 mm module thickness

(2) Membranes: 2× high-temperature rubber membranes (up to 300°C)

(3) Calibration Tools: 5× aluminum foil calibration discs

(4) Consumables: 85% glycerin solution for hydraulic calibration, disposable dust filters

(5) Safety Equipment: Safety goggles (ANSI Z87.1), emergency pressure release key

(6) Documentation: Multilingual quick-start guide and IEC/UL compliance certificates

Test Procedures

(1) Install the PV module specimen securely into the clamping fixture.

(2) Select pressure unit, ramp rate, and holding parameters via the touchscreen interface.

(3) Initiate pressurization and monitor real-time pressure increase.

(4) Maintain holding pressure as specified or continue ramping until rupture occurs.

(5) Record rupture pressure, pressure–time curve, and failure mode automatically.

Maintenance Information

(1) Inspect sealing membranes and clamping fixtures regularly for wear or deformation.

(2) Verify pressure sensor calibration at scheduled intervals.

(3) Clean the test chamber after each rupture test to remove debris.

(4) Check safety valves and electronic cut-off functions before routine operation.

(5) Store the tester in a clean, dry environment to maintain long-term accuracy.

Другие товары поставщика

	Car sun visor end cap production line	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application You use this assembly line in automotive interior manufacturing environments w...
	Torque - to - Failure Tester for Metal Bone - connecting Screws	Whats/App: +86 156 1874 6768 Web: standard-groups.com Torque-to-Failure Tester for Metal Bone-Connecting Screws is a specialized device designed ...
	Programmable Sutherland ink rub tester for R&D and QC	Whats/App: +86 156 1874 6768 Web: standard-groups.com Applications Testing ink abrasion resistance on printed materials Evaluating surface wear...
	Automotive Bed Liner Strength Tester	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Automotive Bed Liner Strength Tester is a precision testing system designed to evaluate...
	Timken Test Machine	Whats/App: +86 156 1874 6768 Web: standard-groups.com The extreme pressure friction testing machine mainly consists of a main frame, a spindle tr...

Все товары поставщика

Похожие товары

	Battery Diaphragm Gas Permeability Tester ISO	Продавец: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Battery Diaphragm Gas Permea...
	Torsion Testing Tester ASTM, JIS, and DIN	Продавец: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Universal Torsion Testing Ma...
	Wire Torsion and Winding Tester ASTM and JIS	Продавец: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Wire Torsion and Winding Tes...
	Metal Wire Repeated Bending Tester ISO/DIS 7801	Продавец: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Metal Wire Repeated Bending ...
	Metal Wire Wrap Tester ISO 4101	Продавец: Standard Groups	Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Metal Wire Wrap Tester is de...