Wire Stripping Machine

• 

Common failures and methods ofwire stripping machine.

1. The length of front wire is different.
A. If the clearance is too large for the left transmission line, adjust the left clearance.
B. The straightener is pressed too tightly. Adjust the straightener adjustment knob.
C. The catheter is not aimed at the center of the knife, and it will adjust the catheter to the center of the blade.

2. The length of the back wire is different.
There is too much clearance for the right transmission line. Adjust the right clearance adjustment disc to the right clearance.

3. The total length is inconsistent with the actual setting parameters.
A. It is longer than the set length, which is due to the systematic error in the mechanical transmission, you need to reduce the value of "L" in the mode.
B. It is shorter than the set length. Because the gap and pressure adjustment between the two wheels of the left transmission line is not suitable, and the value of "L" should be increased in the mode.
C. The length is not consistent because of the failure of the straightener to send the line. It is necessary to adjust the pressure of the right transmission line to the suitable clearance, keep the straightener sent smoothly.

4. The front-end incision is inclined.
It is due to the improper positioning of the catheter. Align the tube with the center of the knife edge.

5. The line head is stripped out of normal while the line end is normal. Some of the incisions are inclined, some of the line cores are cut.
Because the position of the tube is too close to the blade. Adjust the position of the tube, so that the distance between the front end of the tube and the blade is greater than the distance from the line tail (A).

6. The front or the back is cut off in the same bundle line.
Because the edge of the blade is too blocked by too much wire skin and clean it with a brush.

7. The insulation skin is overlaid.
Because there is the excessive pressure on the left and right transmission line. Reduce the left and right pressure wheel.

8. Stripping or stripping in the middle, the length L is qualified, but the size of A.B does not meet the requirements of setting.
A. The wire quality is not qualified, the insulation layer is too loose to the core wire, and the qualified conductor can be replaced.
B. The insulation layer is too soft which is pushed to deformation in machining molting process. The prototype cannot be recovered by external. It is the processing method itself that has the inherent defect. Thus reduce the requirements on the accuracy of length.

Другие товары поставщика

	Wire Stripping Machine	Wire Stripping Machine BJ-HT4 Double line Multi-core Round Cable Cutting and Stripping Machine * Display:7 inch LCD with English Menu...
	AL-936 Label Rewinder	Features ofAL-936 Label Rewinder Automatic speed sync and tension control, without any adjustments. Wind inside or outside, Large roll capacity...
	BJ-02E 4 Drivers Wire Cutting Machine	Operation Video ofBJ-02E 4 Drivers Wire Cutting Machine Specification ofBJ-02E 4 Drivers Model: BJ-02E FOUR DRIVERS Power: AC220/ 50HZ 110V/...
	Multiple Wire Stripping And Twisting Machine BJ-4FN	Features ofMultiple Wire Stripping And Twisting Machine BJ-4FN The machine is suitable for line to coarse computer peripheral cable, tele line, ...
	BJ-1200 Pneumatic Crimping Machine	Specification ofBJ-1200 Pneumatic Crimping Machine Model: BJ-1200 Crimping range: non-insulated terminals≤10mm² Pre-insulated terminal...

Похожие товары

	2 parts fluid mixing dispenser 2 component dosing epoxy PU silicon rubber vacuum system	Продавец: 824681	What is the difference between 2K AB adhesive materials manual potting machine and robot pottingm...
	Horizontal Machining Center	Продавец: Xilong (Shanghai) Machine Tool Co., Ltd.	Horizontal Machining Center parts can automatically finish four sides milling, boring, drilling, ...
	Horizontal Lathe	Продавец: Xilong (Shanghai) Machine Tool Co., Ltd.	As a professional horizontal lathe manufacturerand horizontal lathe factory, Sealion Machine Tool...
	Gantry Machining Center	Продавец: Xilong (Shanghai) Machine Tool Co., Ltd.	SEALION supplies Gantry Machining Center both tables moving type or gantry moving type. Gantry ty...
	Floor Type Boring Mill	Продавец: Xilong (Shanghai) Machine Tool Co., Ltd.	Floor Type Boring Mill is suitable for large size jobs to do milling, boring, drilling, etc. The ...