Thermal Protective Performance Tester (TPP)

• 

The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through a protective composite fabric system - measuring the resulting damage to human skin.

Standards：

BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306

Feature：

Industrial personal computer with analysis software is suitable for severe testing conditions.

Automatic calculation for heat transmission factor and radiant heat transfer index.

Sample holder with force applied kit is easy to operate.

Single pump for shutter movement and cooling water loop.

TPP Specifications：

• Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size

• Copper slug calorimeter sensors (ASTM or ISO)

• ± 0.75°C temperature measurement

• ± 3% radiant heat flux measurement

• Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm)

• Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm)

• Power Requirements: 208-265 VAC, 50/60Hz, Single-phase

• Maximum nominal current 20 Amps

• Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max)

• Cooling Water: Cooling water required, chiller or tap water source is acceptable

• Propane Requirement: Regulated supply at 15 PSI (minimum)

• Water-cooled radiant heat source with 9 quartz (500W) infrared lamps

• Two gas burners with flame detection auto ignition

• Mass flow controller for precise gas control

• Water-cooled protective shutter

• Pneumatic sample carriage and shutter assembly

• Integrated sensor cooling stand (air cooled)

• Emergency stop cuts gas flow, power to lamps and pneumatics

• Tinted tempered glass shield protects operator

• Software safety interlocks monitor water flow, carriage position, burner ignition

Другие товары поставщика

	Carpet Pilling and Fuzzing Tester	Instrument Description This instrument is used to simulate the pilling and fuzzing phenomena that occur during the normal use of carpets. The inst...
	Direcct flame impingement Tester	Introduction The testerisdesignedaccording to the BS476-12:1991.Method of test for ignitability of products by direct flame impingement.The accura...
	Appliance Stability Tester	Product Introduction The device conforms to GB4706-1 Article 20.1. IEC60335-1 Article 20.1 and other standards. The device is composed of a workbe...
	Bio-absorbable Internal Fixation Plates and Screws Tester	Standard YY/T 0509-2009 (China): Specifies mechanical testing protocols for orthopedic plates/screws made of hydrolyzable polymers, including axia...
	Thermal Radiation Performance Tester(RPP)	IntroductionThermal protective clothing and some fire-retardant properties of the material refers that human body carry out security protection who...

Похожие товары

	Reliable Components for Water and Industrial Systems	Продавец: 866507	The Stainless Steel Float Ball is designed for automatic liquid level control and fluid managem...
	Double Convex Lenses	Продавец: Shandong Yanggu Constant Crystal Optics, Inc	Double Convex Lensesare used in image relay applications, or for imaging objects at close conjuga...
	Wedge Prism	Продавец: Shandong Yanggu Constant Crystal Optics, Inc	Wedge prismis an optical element with plane-inclined surfaces, usually the faces are inclined tow...
	Ball Lenses	Продавец: Shandong Yanggu Constant Crystal Optics, Inc	Ball Lensesare commonly used to improve signal quality in fiber coupling applications, or for use...
	KAZUKI 6-GFM-33 12V33Ah AGM Gel Battery	Продавец: Xin Tang Shallow Power Supply Co.,LTD	KAZUKI 6-GFM-33 12V33Ah AGM Gel Battery Small Office & Retail UPS Backup Power Systems...