PLC liquid crystal touch impact testing machine (simple suspension)

• 

Product Introduction:

Liquid crystal touch impact testing machine is mainly used for hard plastics (including sheet, pipe, plastic profile)， reinforced nylon, glass fiber reinforced plastic, ceramic, cast stone, electrical insulation materials and other non-metallic materials impact toughness measurement, widely used in the chemical industry, scientific research units, universities and other quality testing departments.

Standards:

GB/T 11022-2020. GB/T 3906-2020. JB/T 10840-2008.GB/T 7251.1-2013 ，GB/T 7251.4-2017.GB/T 7251.5-2017 ，GB/T 20641-2014

GB/T 20138-2006 ，GB/T2423.55-2006 ，Q/GDW11008-2013

Main features:

Not poor quality: the use of high hardness and high-precision bearings, and the use of shaftless photoelectric sensors, fundamentally eliminate the loss caused by friction, to ensure that the friction energy loss is far less than the standard requirements.

Intelligent prompt: According to the impact of the situation, intelligent prompt working status, always interact with the experimenter, to ensure the success rate of the test.

Friendly interface: there are parameter setting interface - result query interface - measurement interface - system setting interface, each operation has a clear user prompt, you can record 10 test records, you can choose domestic and international standards, you can choose Chinese and English.

Accurate measurement: In full accordance with the provisions of the new standard, after 10 swing cycles for a calculation of energy loss, each measurement to go through 3 times to average, to ensure the accuracy of energy loss.

Performance parameters:

1. Simple beam impact testing machine

- Impact speed: 2.9m/s

- Impact energy: 1/2/4/5J

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 230mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

2. Cantilever beam impact testing machine

- Impact speed: 3.5m/s

- Impact energy: 1J; 2.75 J; 5.5 J; 11J; 22J(3 hammers, customer's choice)

- Maximum friction loss energy: <0.5%

- Pendulum prelift Angle: 150±1°

- Strike center distance: 335mm

- Power supply: 220VAC-15% —— 220VAC+10%, 50Hz(single-phase three-wire system)

Другие товары поставщика

	Film punching machine ASTM	Meet the standard: GB/T1528; GB/T529; GB/T8083; GB/T 15340.ASTM Technical parameters: Travel range :100mm Blanking force: about 20kN Table siz...
	Abrasion testing machine / Abrasion Testers	Product Introduction Wear testing machine is used with the balance, specially testing the wear resistance of rubber products such as soles, tires,...
	Plastic Smoke Density Tester ISO 5659	Standards: GB/T8323.2-2008: Plastics - Smoke generation - Part 2: Determination of optical density by a single-chamber test ISO 5659-1: Plastics -...
	Geotextile Dynamic Puncture Tester ISO 13433	Scope of application: It is used to test the penetration ability of various geomaterials to resist steel cones falling from a fixed height, so as ...
	Bag fastener magnetic buckle testing machine / Luggage Tester	Product Introduction: This machine is mainly used to test the durability of the finished magnetic buckle under the action of tension Implementati...

Похожие товары

	Bottle Wall and Bottom Thickness Tester	Продавец: Standard Group (Hong Kong) Limited	The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha...
	Pinhole Tester / Pinhole Testing Equipment	Продавец: Standard Group (Hong Kong) Limited	The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ...
	Cork Puncture and Chip Detection Instrument	Продавец: Standard Group (Hong Kong) Limited	The rubber stopper puncture debris detector is a device specifically used to detect the number of...
	Aluminum Ointment Tube Toughness Tester	Продавец: Standard Group (Hong Kong) Limited	The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind...
	Vacuum leak tester / Vacuum leak instrument	Продавец: Standard Group (Hong Kong) Limited	Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott...