Micro Controll High-temperature Friction Tester

Applicable Standards

When conducting tests, the microcomputer - controlled high - temperature friction testing machine usually needs to comply with the following relevant national or international standards: - GB/T series standards: Relevant regulations on friction and wear testing in Chinese national standards, such as GB/T 12583 - 98 *Method for Determination of the Extreme - Pressure Properties of Lubricants (Four - ball Machine Method)*, etc.

Main Purposes

The microcomputer - controlled high - temperature friction testing machine is a device specifically designed for testing the frictional properties of materials in high - temperature environments. Its main purposes include, but are not limited to, the following aspects:

Material R & D and Evaluation

- Used to evaluate the friction and wear properties of various materials under high - temperature conditions, including metals, non - metals, coatings, rubbers, plastics, ceramics, etc.

- Helps in the research and development of new high - temperature - resistant materials and improves the high - temperature frictional properties of materials.

Lubricant and Oil Product Testing

- Test the frictional properties of lubricants, hydraulic oils, internal combustion engine oils, gear oils, etc. at high temperatures, and evaluate their lubrication effects and anti - wear capabilities. - Provide data support for the R & D, improvement, and quality control of lubricants and oil products.

Durability Testing of Mechanical Components

- Simulate the actual working conditions of mechanical components in high - temperature environments, test their friction and wear properties, and evaluate the durability and reliability of the components. - Contribute to optimizing mechanical designs and improving the service life and performance stability of mechanical components.

Technical parameters

Maximum test force 100KN

Tester accuracy 0.5 level

Test force measurement range 0.2%-100%FS All the way without gearing

Test force accuracy ±0.5% or less

Test force resolution 1/±300000 of the maximum test force (the whole resolution is unchanged)

Deformation measurement range 0.2%-100%FS

Relative error of the deformation value of the value of ±0.5% or less Within ±0.5%

Distinguishing power of deformation 1/±300000 of the maximum deformation

Dimensions of high and low temperature chamber 300mm*300mm*400mm

Temperature range Room temperature～600℃

Temperature fluctuation ±1℃

Relative error of displacement ±0.5% of the indicated value

Distinguishing power of displacement 0.05μm

Adjustment range of force rate 0.01-5%FS/S

Relative error of force rate ±0.5% of the setting value 0.5% of set value Within ±0.5% of set value

Transformation rate adjustment range 0.02-5%FS/S

Relative error of transformation control rate Within ±0.5% of set value

Transverse beam speed adjustment range 0.01-500mm/min

Relative error of transverse beam speed Within ±1.0% of set value for speed < 0.01mm/min; within ±1.0% of set value for speed ≥ 0.01mm/min. mm/min, within ±0.2% of the set value

Control range of constant force, constant deformation and constant displacement 0.5%-100%FS

Control accuracy of constant force, constant deformation and constant displacement When the set value is <10%FS, it is within ±1% of the set value; when the set value is ≥10%FS, it is within ±0.1% of the set value

Effective tensile space 700mm

Effective test width 600mm

Main machine appearance Dimensions (L×W×H) 800×600×2000 (mm)

Power supply 220V±10%,50Hz

Weight of mainframe about 500kg

Другие товары поставщика

	Photovoltaic module outdoor exposure test system	Standard IEC 61215: Terrestrial Photovoltaic (PV) Modules – Design Qualification and Type Approval IEC 61730: Photovoltaic (PV) Module Sa...
	Fabric light transmittance test machine	Light transmittance test machine for fabric is used to determine the total visible light transmittance of the fabric to evaluate the shading proper...
	Guide pin anchoring force tester	Product introduction The anchoring force test of the guide needle can ensure the anchoring effect of the mammary positioning filament within the t...
	Plastic Pipe Hydrostatic Pressure Burst Tester	Standard ISO 1167: For thermoplastics pipe systems under constant internal pressure. ASTM D 1598: Standard test method for time-to-failure of pla...
	Dry Sand Rubber Wheel Wear Tester	Standard ASTM G65 JBT_7705 Applicable standards Dry and wet abrasive wear testing machines usually need to follow certain standards and specifi...

Все товары поставщика

Похожие товары

	Plastic Smoke Density Tester F313	Продавец: Standard International Group (HK) Limited	The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ...
	Xenon Test Chamber	Продавец: Standard International Group (HK) Limited	Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli...
	Single Cable Vertical Flame Tester	Продавец: Qinsun Instruments Co., LTD	Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ...
	Safety Helmet Flammability Tester	Продавец: Qinsun Instruments Co., LTD	Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda...
	Furniture flammability tester	Продавец: Qinsun Instruments Co., LTD	Product details Furniture flammability tester is mainly used to test the combustion performance ...