Rubber Hose Outer Coating Abrasion Testing Equipment
Product Introduction:
Rubber hose outer coating Wear testing machine for hydraulic hoses and other similar types of hoses with fabric or steel wire reinforced outer coating with a smooth and flat surface.
Test method:
1. Install the assembled sample and mandrel on the test device, and ensure that the sample has no axial movement and (or) rotation.
2. place the abrasive tool to make contact with the sample, apply the vertical static pressure F specified in the product standard, and start the machine. If the force F is not specified in the product standard, the applied vertical static pressure should be 50N±0.5N.
3. the test is carried out until the specified number of cycles is completed, and then the sample assembly is removed from the test device, and the sample with or without a core shaft is weighed again as the initial weighing. It is important to remove any particles attached to the outer coating before weighing.
Test standard:
GB/T 12721-2007 - Determination of abrasion resistance of rubber hose outer coating
ISO 6945:1991 - Determination of the abrasion resistance of rubber hose cladding
KS M ISO 6945-2013 - Determination of the abrasion resistance of the outer coating of rubber hoses
EN ISO 6945-1996 - Determination of the abrasion resistance of rubber hose outer coatings
DS/ISO 6945-1984 Determination of wear resistance of rubber hose cladding
Main parameters:
1. reciprocating frequency: 1.25Hz(45 RPM)
2. cycle stroke: 200mm
3. loading static pressure: 50N±0.5N(other pressure weights can be customized processing)
4. Mandrel length: 150mm
5. shaft diameter: 5mm, 8mm, 10mm, 13mm, 16mm, 19mm, 22mm, 25mm, 32mm, 38mm, 45mm, 51mm, optional three, can also provide dimensional processing
Отправить запрос, связаться с поставщиком
Другие товары поставщика
| Sliding bearing PV friction testing machine | Standard This machine is mainly applicable to GB 7948-1987 plastic bearing limit PV test method, JB/T 7381-2010 powder metallurgy oil bearing PV v... | |
| Dental Implants Fatigue Tester | Standard ISO 14801:2016: Specifies dynamic fatigue testing protocols for endosseous dental implants, including load ratios, frequency, and failure... | |
| Finger Tactile Tester Sensor | Finger Tactile Sensor is a "sensor that measures natural finger operations"with a built-in contact force sensor and a 3-axis acceleration sensor. ... | |
| Prefilled Syringe Plunger Force Tester | The Prefilled Syringe Plunger Force Tester is widely used in the medical device industry, mainly for testing the push - force performance of prefil... | |
| Photovoltaic module outdoor exposure test system | The Photovoltaic Module Outdoor Exposure Test System is designed to simulate real-world environmental conditions for accelerated aging and performa... |
Похожие товары
| Plastic Smoke Density Tester F313 | Продавец: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... | |
| Xenon Test Chamber | Продавец: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... | |
| Single Cable Vertical Flame Tester | Продавец: Qinsun Instruments Co., LTD | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... | |
| Safety Helmet Flammability Tester | Продавец: Qinsun Instruments Co., LTD | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... | |
| Furniture flammability tester | Продавец: Qinsun Instruments Co., LTD | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
















