Wyzenbeek or Oscillatory Abrasion Tester

Product introduction:

Wyzenbeek wear resistance tester, also known as Oscillatory wear resistance tester, is used to test the wear resistance of fabrics against standard friction media or metal mesh surface friction movement, especially suitable for automotive decoration and furniture textile product. Instrument regulations American standard. There are 4 friction heads and electronic counter to control the running cycle.

Features：

Easy to control due to the precision electronic digital counter.

The protective cover provides protection and thus more safety.

Four abrasion heads to test samples simultaneously, thus greater efficiency.

Complied Standards：

ASTM D3597. ASTM D4157. CFFA-1A, FED-STD-191/5304. GM2756M, LP-463KB-06-01. LP-463KC-04-01. SAE J 948. SAE J1530. Toyota TSL 5101G 3.9.4 etc...

Working principles：

Install the long strip of sample fabric on the front and rear clamps of the friction head, and apply a certain tension force. Install the friction medium on the arc-shaped friction table to make the sample contact the friction medium and apply a certain load On the sample. The friction table swings back and forth to rub the sample, and after a certain number of frictions, evaluate the change in the breaking strength of the sample

Standard configuration：

Main machine 1set

Imported rubber pad 8pcs/pack

Imported metal mesh 4pcs/pack

Imported standard abrasive No. 10 cotton canvas (60inches X 5yards)

Power cable 1pcs

Manual 1pcs

Technical parameter：

1. Modern ergonomic design.

2. The suction device connected to the auxiliary vacuum cleaner.

3. Sealed transmission ensures quiet operation.

4. Test position: 4 heads.

5. Friction table: Curve surface-R100mm, length-400mm

6. Swing radian: 76+/-2mm.

7. Friction rate: 90+/-1/min(double friction).

8. Tension adjustment weight: 340g (tension adjustment range 8.9N-22.25N)

9. Load adjustment weight: 150g (load adjustment range 8.9N-17.8N)

10. Sample tension: 17.8N (adjustable)

11. Sample load: 13.4N (adjustable)

12. Sponge rubber pressure pad: 50X50mm(+/-1mm)

13. Instrument material: Stainless

14. Surface finishing: painting

15. Sample dimension: 245X73mm

16. Product dimension: 50X50X60 (LXWXH)

Другие товары поставщика

	Geosynthetics thickness tester	Scope of application: Used to determine the thickness of various geosynthetic materials under specified pressure and time. The sample is placed on...
	Sand and Dust Test Chamber for Automotive Connectors	Operating Conditions: Ambient temperature: 5°C～+28°C (average temperature within 24 hours ≤28°C); Ambient humidity: ≤85% Techni...
	Automotive Wire Scratch Resistance Tester	Standards The tester adheres to global standards for material abrasion testing, including: ISO 6722-1(Road vehicles – Electrical cables &...
	MMT Liquid Water Separation Tester-QINSUN
	Horizontal Vertical Combustion Tester	IntroductionHorizontal and vertical combustion testeris to simulate the early situation of a fire around the electrical environment .By simulating ...

Все товары поставщика

Похожие товары

	Seat Bumping and Creep Test Bench	Продавец: Standard International Group (HK) Limited	This test bench is used for simulating the car seat bumping and creep situation when a car is run...
	Automobile seat belt fixed point test bench	Продавец: Standard International Group (HK) Limited	Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur...
	Impact strength tester for car seat headrest	Продавец: Standard International Group (HK) Limited	Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi...
	Impact strength tester for car seat launching headrest	Продавец: Standard International Group (HK) Limited	Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w...
	Automobile Headrest Strength Tester	Продавец: Standard International Group (HK) Limited	Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me...